Install Mounting Hardware
| cci-readerinstall-kit |
|---|
| KitID | 917 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 813 |
|---|
| KitDesc | Card Only - Coin Model |
|---|
|
Remove coin drop and coin box. Insert the C-5771 Metercase Bracket over the front of the metercase. Attach using the C-0303 Topload Mounting Bolt from the inside of the metercase. Optional: Apply the C-5027 Label on or near the card reader for any accepted credit card issuers.
|
| Cci readerinstall kit |
|---|
|
Remove existing coin box and coin drop. Insert C-0911 Metercase Bracket into the metercase and secure using the C-0301 Topload Mounting Bolt. Attach reader to C-0911 Metercase Bracket using C-0141 Screws once all harnesses are connected. Cover mounting screw holes using C-0015 Cover Label.
|
...
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
...
Place the C-6700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
...
| KitID | 906 |
|---|
| KitDesc | Card Only - Card Ready Models |
|---|
...
Place the C-6700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
...
| KitID | 860 |
|---|
| KitDesc | Card Only - Coin Ready Models |
|---|
...
Remove existing coin box and coin drop.
...
Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.
...
Run reader harnesses through the circular opening in the C-6911 Metercase Bracket.
...
Insert C-6911 Metercase Bracket into the metercase and secure using the C-0303 Topload Mounting Bolt.
...
| cci-readerinstall-kit |
|---|
|
Tap the incoming AC power wires using the C-5101 Spade Taps.
For 120v models: L1, N, and Ground wires
Connect the three wires from the C-5210 Power Adapter Harness to theC-5101 Spade Taps.Connect the Blue wire to the L1 tap.
Connect the Brown wire to the N tap.
Connect the Green/Yellow wire to the Ground tap.
Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connector on the C-5602R1 Power Converter.
Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connector on the C-5500 Power Extension Harness.
Run the C-5500 Power Extension Harness to the reader mounting location.
...
| cci-readerinstall-kitstep |
|---|
| KitID | 693 |
|---|
| KitDesc | Coin Drop - Factory Optical |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-5362 Coin Sense Harness to the harness connected to the Coin Drop.
|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 721 |
|---|
| KitDesc | Coin Drop: Factory |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
| KitID | 1004 |
|---|
| KitDesc | Pulse - Debit/AA3 Connection |
|---|
|
Connect the C-5364 Machine Start Harness to the Debit/AA3 connector on the Machine Control Assembly. If needed, use the C-126-MLV-EXT15 Extension Harness to extended the reach of the harness.
|
Connect and Mount Reader
...
Machine Configuration
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | MayTag Gen1 MLV+ Pulse |
|---|
| PageWithExcerpt | _Machine Configuration |
|---|
|
...