Versions Compared

Old Version 6

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID616
    KitDescCoin and Card
    step
    componentMounting

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to Touchscreen Reader Mounting Guide (F2 & F3) for further instructions.
    cci-readerinstall-kit
    KitID818
    KitDescCard Only

    1. Remove existing coin box.

    2. Bend the side tabs of the C-0936 Vault Mount Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

    3. Attach the C-0133 8-32 x 1-1/2" Standoffs to the C-0936 Vault Mount Bracket.

    4. Attach reader to the Bracket using C-0141 Screw.

    Cci readerinstall kit
    KitID841
    KitDescCoin and Card
    Cci readerinstall kit
    KitID948
    KitDescCard Only

    1. Remove existing coin box and coin drop.

    2. Bend the side tabs of the C-6936 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.

    3. Attach the C-5414 Mounting Bracket to the C-6936 Vault Bracket using C-0144 Screws.

    4. Apply C-5035 Label over the coin drop opening.

    ...

    step
    componentPower

    Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  • Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  • Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kit
    KitID794

    ...

    step
    componentCoin Sense

    Cci readerinstall kit
    Cci readerinstall kit
    689
    KitID
    KitDescCoin Drop: Factory

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5357 Coin Sense Harness to the harness connected to the Coin Drop.

    KitID690
    KitDescCoin Drop: Bare Wires

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5358 Coin Sense Harness to the harness connected to the Coin Drop.

      1. Match each of the colored wires from the coin drop to the matching wire on the coin sense harness.

    cci-readerinstall-kit
    KitID716
    KitDescCoin Drop: Edge Connector

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6357 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID830
    KitDescPulse - Terminal w/Block

    1. Attach the C-5313 Terminal Block to the Machine Control Assembly.

    2. Connect the C-5356 Machine Start Harness to the Positions 2 and 3 on the C-5313 Terminal Block.

      1. Terminal block positions are numbered 0-6. Position 0 is closest to the board edge.

    Connect the C-5353R1 Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID655
    KitDescPulse - Edge Connector
    step
    componentStart

    Cci readerinstall step
    componentReader

    ...