Install Mounting Hardware
| cci-readerinstall-kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 616 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.
| Cci readerinstall kit |
|---|
| KitID | 791 |
|---|
| KitDesc | Card Only - 10° Front Panel Coin Models |
|---|
|
Remove existing coin box and coin drop/slide. Remove vault service switch connections from the switch and bridge using the C-5365 Bypass Harness. Install C-5765-W Vault Bracket over the metercase opening. Secure in place using C-1059 Kep Nuts and C-1070-W Washers. If installing on a coin slide equipped model the two holes next to the coin slide bolt will need to be enlarged about a 1/4" to allow the mounting studs to pass through the metercase.
Apply C-5027 Label on or near the reader if required for location.
|
| Cci readerinstall kit |
|---|
| KitID | 857 |
|---|
| KitDesc | Card Only - 10° Panel Coin Models |
|---|
|
Remove existing coin box and coin drop. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using C-5702 Chase Nipple and C-5703 Lock Nut. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1 Metercase Bracket. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the C-1059 Kep Nuts and C-1070-W Washers.
|
...
| KitID | 905 |
|---|
| KitDesc | Card Only - Card Ready Models |
|---|
...
Place the C-5700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
...
| KitID | 906 |
|---|
| KitDesc | Card Only - All Card Models |
|---|
...
Place the C-6700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
...
| KitID | 910 |
|---|
| KitDesc | Card Only - Flat Front Panel Coin Models |
|---|
...
Remove coin drops and coin boxes.
...
Remove vault service switch connections from the switch and bridge using the C-5365 Bypass Harness.
...
Take the C-0940 Vault Cover and bend the inner tabs outward.
...
Insert the C-0940 Vault Cover into the coin box opening. The previously bent tabs should catch the inner lip of the coin vault and secure the bracket in place.
...
Place the C-5700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Suggested mounting location: Coin drop opening.
...
| cci-readerinstall-kit |
|---|
| KitID | 581 |
|---|
| KitDesc | ACA Controls |
|---|
|
Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly. Connect the green wire to a chassis ground. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
| Cci readerinstall kit |
|---|
| KitID | 837 |
|---|
| KitDesc | Titanium Controls |
|---|
|
Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
...
| KitID | 595 |
|---|
| KitDesc | Hybrid Coin Slides |
|---|
...
Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
...
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
...
| cci-readerinstall-kit |
|---|
| KitID | 674 |
|---|
| KitDesc | Coin Drop: Optical Coin Drops |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 677 |
|---|
| KitDesc | Coin Drop: Coin Slide |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-5253 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 700 |
|---|
| KitDesc | Factory Standard Coin Drop |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 704 |
|---|
| KitDesc | Factory Standard Coin Slide |
|---|
|
Locate the micro switch on the coin slide assembly for the upper pocket. Disconnect the harness connected to the microswitch and connect C-6253 Coin Sense Harness to the spade tabs on the micro switch.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
| KitID | 645 |
|---|
| KitDesc | Pulse - Coin Connection |
|---|
|
Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.| step |
|---|
|
|
| cci-readerinstall-kitstep |
|---|
| KitID | 582 |
|---|
| KitDesc | Serial Communication / Serial Pulse |
|---|
|
Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board. |
|
| cci-readerinstall-kit |
|---|
| KitID | 636 |
|---|
| KitDesc | Hybrid Coin Slide Switch |
|---|
|
Connect the C-5256 Machine Start Harness to the the harness previously connected to the coin slide microswitch spade tabs.
|
Connect Stack Add-On Components
| Cci readerinstall kit |
|---|
| KitID | 1023 |
|---|
| KitDesc | Serial Stack Add-On - Card Only - Card Models |
|---|
|
Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board on the lower pocket control.
|
| Cci readerinstall kit |
|---|
| KitID | 938 |
|---|
| KitDesc | Serial Stack Add-On - Coin and Card Install |
|---|
|
Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board on the lower pocket control. Disconnect the Coin Drop from the Machine Control Assembly lower pocket control. Connect the C-6250 Coin Sense Harness to the harness connected to the lower pocket's Coin Drop.
|
Connect and Mount Reader
...
Machine Configuration
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | ACA Configuration |
|---|
| PageWithExcerpt | _Machine Configuration |
|---|
|
...