Install Mounting Hardware
| cci-readerinstall-kitstep |
|---|
| KitID | 917 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to F1 FasCard Reader Mounting Guide for further instructions. |
|
| cci-readerinstall-kit |
|---|
| KitID | 789 |
|---|
| KitDesc | Card Only - Coin Models |
|---|
|
Remove existing coin box and coin drop. Install C-0963 Drop Cover into the coin drop opening. Secure using C-1062 Keps Nuts. Bend the side tabs of the C-0936 Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket. Attach the C-0132 Standoffs to the Bracket. After connecting harnesses to the reader, attach to C-0936 Bracket using C-0141 Screws. Optional: Apply C-5027 Label on, or near the reader for any accepted credit card issuers.
|
| Cci readerinstall kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| Cci readerinstall kit |
|---|
| KitID | 667 |
|---|
| KitDesc | Card Only - Small Coin Vault |
|---|
|
Install the C-5702 Chase Nipple into the C-5414 F2 Mounting Bracketusing the C-5703 Nut.Feed the remaining harness ends through the open face of the Coin Vault.
Spread the C-6936 Vault Mount Bracket wings outward before insertion to lock bracket into place.
Feed remaining harness ends through the C-6936 Vault Mount Bracket.
Insert the C-6936 Vault Mount Bracket into the Coin Vault.
Feed the remaining harness ends through the combined C-5414 F2 Mounting Bracket.
Secure the combined C-5414 F2 Mounting Bracketto the C-6939 Vault Mount Bracket with the C-0144 Screws.| Cci readerinstall kit |
|---|
| KitID | 840 |
|---|
| KitDesc | Card Only - Large Coin Vault |
|---|
|
Attach the C-5414 F2 Mounting Bracket to the C-6602 Spacer Plate using the C-5702 Chase Nipple and the C-5703 Nut.
Feed the remaining harness ends through the open face of the Coin Vault.
Spread the C-6602 Vault Mount Bracket wings outward before insertion to lock bracket into place.
Feed remaining harness ends through the C-6602 Vault Mount Bracket.
Insert the C-6602 Vault Mount Bracket into the Coin Vault.
Feed the remaining harness ends through the combined C-5414 F2 Mounting Bracket.
Secure the combined C-5414 F2 Mounting Bracketto the C-6602 Vault Mount Bracket with the C-0144 Screws.| Cci readerinstall kit |
|---|
| KitID | 906 |
|---|
| KitDesc | Easy Card Ready |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.
...
| cci-readerinstall-kit |
|---|
|
Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.240vac- Connect Blue wire to the L1 tab, and the Brown wire to the L2 tab on the terminal block.
Secure the green wire beneath the ground screw.
Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
...
| cci-readerinstall-kit |
|---|
| KitID | 677 |
|---|
| KitDesc | Coin Drop: Factory Mechanical Switch |
|---|
|
Disconnect the factor coin drop harness from the microswitch on the coin drop. Connect the C-5253 Coin Sense Harness to the microswitch on the the coin drop.
|
| Cci readerinstall kit |
|---|
| KitID | 679 |
|---|
| KitDesc | Coin Drop: Factory Optical Sensor |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-5258 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 696 |
|---|
| KitDesc | Coin Drop: Imonex w/EM Board |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-5382 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 704 |
|---|
| KitDesc | Coin Drop: Factory - Micro Switch |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 707 |
|---|
| KitDesc | Coin Drop: Factory |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 723 |
|---|
| KitDesc | Coin Drop: Factory |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
| KitID | 634 |
|---|
| KitDesc | Pulse - Optical Sensor |
|---|
|
Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 636 |
|---|
| KitDesc | Pulse - Micro Switch |
|---|
|
Connect the C-5256 Machine Start Harness to the harness previously connected to the coin switch on the Coin Drop.
|
Connect and Mount Reader
...
Machine Configuration
No special configuration required.
...