Versions Compared

Old Version 7

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID616
    KitDescCoin and Card
    step
    componentMounting

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID841
    KitDescCoin and Card
    Cci readerinstall kit
    KitID945
    KitDescCard Only

    1. Place the C-5414 Mounting Bracket on top of the C-6601 Spacer Plate.

    2. Place both Mounting Bracket and Spacer Plate over the mounting hole previously used by the coin drop.

    3. Place the C-6701 Adapter Plate on the opposite side of the machine panel and secure in place using the C-5416 Screws.

    4. Place the C-5710 Rubber Grommet into the circular opening of the C-5414 Mounting Bracket.

    ...

    step
    componentPower

    Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  • Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  • Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

    • cci-readerinstall-kitstep
    KitID595

    ...

    componentCoin Sense

    cci-readerinstall-kitstep
    KitID685
    KitDescCoin Drop: Factory

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5343 Coin Sense Harness to the harness connected to the Coin Drop.

    ...

    componentStart

    cci-readerinstall-kitstep
    KitIDcomponent652
    KitDescPulse

    1. Connect the C-5344 Machine Start Harness to the Coin 1 connection on the Machine Control Assembly.

    Optional: Stack Add-on Installation

    Extras

    cci-readerinstall-kit
    KitID935
    KitDescPulse

    1. Run C-5344 Machine Start Harness and C-6348 Coin Sense Harness to the second Machine Control Assembly.

    2. Connect C-5344 Machine Start Harness to the Coin 1 connection and the C-6348 Coin Sense Harness to the coin drop for the second Machine Control Assembly.

    3. Connect the C-6400 Stack Add-on Board to port 5 (Serial Connection Port) on the F2 reader.

      1. Connect the Machine Start Harness connected to the upper pocket Machine Control Assembly to Port 2 on the reader.

      2. Connect the Machine Start Harness connected to the lower pocket Machine Control Assembly to the Stack Add-on Board.

    4. Connect the Coin Sense Harness connected to the upper pocket Coin Drop to port 3 (Coin 1 Sense Harness Connection Port) on the F2 reader.

    5. Connect the Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the F2 reader.

    Connect and Mount Reader

    Expand
    titleF1 Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF1 Reader
    PageWithExcerpt_Reader Ports

    1. Feed remaining harness ends through the mounting hole as described in F1: FasCard Reader Mounting Guide.

    2. Connect the free end of the C-5344 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    3. Connect the free end of the C-5343 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.

    5. Secure the FasCard reader to base as described in the F1: FasCard Reader Mounting Guide.

    Expand
    titleF2, F3, Flex, FlexRF

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.

    2. Connect the free end of the C-5344 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.

    3. Connect the free end of the C-6348 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

    4. Connect the free end of the C-5500 Power Harness to port 1.

    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    step
    componentReader

    Cci readerinstall footer