Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    step
    componentMounting

    Place C-5763 TWL Bracket in the intended mounting location. Using the bracket, mark the location of all four mounting holes.
    Drill a hole at each marked location using a 3/16" drill bit.
    Attach C-5414 Mounting Bracket to the front of C-5763 using two C-5420 screws.
  • Mount the C-5763 TLW Bracket using four C-5420 Screws and fasten from the inside of the panel.

  • Place the C-5700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kit
    KitID906
    KitDescCard Only - Rear Control Card Models
    Cci readerinstall kit
    KitID917
    KitDescCoin and Card
    Cci readerinstall kit
    KitID791
    KitDescCard Only - 10 Degree Front Panel Coin Drop Models
    1. Remove existing coin box and coin drop.

    2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

    3. Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

    ...

    KitID905
    KitDescCard Only - Card Ready Models

    ...

    Place the C-5700-TEMP Drill Template on the desired mounting location.

    ...

    Verify included harnesses will reach desired location without encountering interference from internal machine components.

    ...

    KitID861
    KitDescCard Only - Rear Control Coin Drop Model

    ...

    Remove the coin drop and coin box.

    ...

    Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.

    ...

    Attach the C-5760-A Adapter Bracket to the C-6762 Mounting Bracket to the captured nut on the inside of the C-6762 Mounting Bracket.

    ...

    Run all reader harnesses through the metercase and out the opening where the coin drop normally mounts.

    ...

    Run all reader harnesses through the circular opening on the C-6762 Mounting Bracket.

    ...

    Install the C-6762 Mounting Bracket into the front opening of the metercase so the two threaded posts of the C-5760-A Adapter Bracket line up with the openings for the coin slots. Secure in place using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

    ...

    KitID857
    KitDescCard Only - 10° Panel Coin Model

    ...

    Remove existing coin box and coin drop.

    ...

    Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

    ...

    Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

    ...

    Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

    ...

    step
    componentPower

    cci-readerinstall-kitstep
    KitIDcomponent595KitDescCoin Slide Models - Tap 120/240v Power
    1. Use the C-5101 Spade Taps on the incoming power.

      1. Tap the L1 wire.

      2. Tap the N wire.

      3. Tap the Ground wire.

    2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

      1. Connect the blue wire to the L1 wire.

      2. Connect the brown wire to the N wire.

      3. Connect the green/yellow wire to the Ground wire.

    3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

    4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

    Cci readerinstall kit
    KitID581
    KitDescACA Controls - 12VDC Accessory Power
    1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

      1. Secure the green wire beneath the ground screw.

    2. Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

    Cci readerinstall kit
    KitID837
    KitDescTitanium Controls - 24VAC Transformer
    1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.

    2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

    ...

    Sense

    ...

    cci-readerinstall-kit
    KitID674
    KitDescCoin Drop: ACA Control Models
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

    Cci readerinstall kit
    KitID677
    KitDescCoin Drop: Coin Slide Models
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5253 Coin Sense Harness to the micro switch on the coin slide.

    Cci readerinstall kit
    KitID700
    KitDescCoin Drop - Factory Optical
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

    Cci readerinstall kit
    KitID704
    KitDescCoin Slide - Factory Coin Slide Switch
    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Slide Switch.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID645
    KitDescPulse - Coin Connection
    1. Connect the C-5300-NC Machine Start Harness to the harness previously connected to the coin drop.

    Connect the C-5256 Machine Start Harness to the harness previously connected to the Coin Slide Switch.
    Cci readerinstall kit
    KitID636
    KitDescPulse - Coin Slide Switch
    step
    componentStart

    cci-readerinstall-kitstep
    KitID582
    KitDescSerial Communication / Serial Pulse
    1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

    Connect and Mount Reader

    ...

    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    ...