Versions Compared

Old Version 8

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Place C-5763 TWL Bracket in the intended mounting location. Using the bracket, mark the location of all four mounting holes.
Drill a hole at each marked location using a 3/16" drill bit.
Attach C-5414 Mounting Bracket to the front of C-5763 using two C-5420 screws.
Mount the C-5763 TLW Bracket using four C-5420 Screws and fasten from the inside of the panel.
cci-readerinstall-kit
KitID906
KitDescCard Only - Rear Control Card Models
step
componentMounting

  • Remove existing coin box and coin drop.

  • Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.

  • Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.

    • Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1Metercase Bracket.

  • Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.

    • cci-readerinstall-kit
    KitID791
    KitDescCard Only - 10 Degree Front Panel Coin Drop Models

    1. Remove existing coin box and coin drop.

    2. Remove connections to coin vault service switch and bridge connections using C-5365 Bypass Harness.

    3. Install C-5765-W Metercase Bracket over the front of the metercase and secure using the C-1059 Kep Nut, and C-1070-W Washer.

    Cci readerinstall kit
    KitID857
    KitDescCard Only - 10° Panel Coin Model

    ...

    step
    componentPower

    cci-readerinstall-kit
    KitID595
    KitDescCoin Slide Models - Tap 120/240v Power

    1. Use the C-5101 Spade Taps on the incoming power.

      1. Tap the L1 wire.

      2. Tap the N wire.

      3. Tap the Ground wire.

    2. Take the C-5210 Power Adapter Harness and connect the red tab connectors to the following wires:

      1. Connect the blue wire to the L1 wire.

      2. Connect the brown wire to the N wire.

      3. Connect the green/yellow wire to the Ground wire.

    3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connection on the C-5602R1 Power Converter.

    4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connection on the C-5500 Power Extension Harness.

    Cci readerinstall kit
    KitID581
    KitDescACA Controls - 12VDC Accessory Power

    1. Connect the C-6204-40 12VDC Power Harness to the H10 connection on the machine control assembly.

      1. Secure the green wire beneath the ground screw.

    2. Connect the opposite end of the C-6204-40 Power Adapter Harness (3-pin molex) to the F2 reader.

    Cci readerinstall kit
    KitID837
    KitDescTitanium Controls - 24VAC Transformer

    1. Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel.

    2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.

    ...

    step
    componentCoin Sense

    cci-readerinstall-kit
    KitID674
    KitDescCoin Drop: ACA Control Models

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

    Cci readerinstall kit
    KitID677
    KitDescCoin Drop: Coin Slide Models

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5253 Coin Sense Harness to the micro switch on the coin slide.

    Cci readerinstall kit
    KitID700
    KitDescCoin Drop - Factory Optical

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.

    Cci readerinstall kit
    KitID704
    KitDescCoin Slide - Factory Coin Slide Switch

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Slide Switch.

    Connect Machine Interface Harness

    Connect the C-5300-NC Machine Start Harness to the harness previously connected to the coin drop.
    Cci readerinstall kit
    KitID645
    KitDescPulse - Coin Connection
    step
    componentStart

    cci-readerinstall-kit
    KitID636
    KitDescPulse - Coin Slide Switch

    1. Connect the C-5256 Machine Start Harness to the harness previously connected to the Coin Slide Switch.

    Cci readerinstall kit
    KitID582
    KitDescSerial Communication / Serial Pulse

    1. Connect the C-5240 Machine Start Harness to the H3 connection on the Machine Control Assembly.

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    ...