Install Mounting Hardware
| cci-readerinstall-kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 616 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-5700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.
| Cci readerinstall kit |
|---|
| KitID | 791 |
|---|
| KitDesc | Card Only - 10° Front Panel Coin Models |
|---|
|
Remove existing coin box and coin drop/slide. Remove vault service switch connections from the switch and bridge using the C-5365 Bypass Harness. Install C-5765-W Vault Bracket over the metercase opening. Secure in place using C-1059 Kep Nuts and C-1070-W Washers. If installing on a coin slide equipped model the two holes next to the coin slide bolt will need to be enlarged about a 1/4" to allow the mounting studs to pass through the metercase.
Apply C-5027 Label on or near the reader if required for location.
|
| Cci readerinstall kit |
|---|
| KitID | 857 |
|---|
| KitDesc | Card Only - 10° Panel Coin Models |
|---|
|
Remove existing coin box and coin drop. Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness. Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using C-5702 Chase Nipple and C-5703 Lock Nut. Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1 Metercase Bracket. Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the C-1059 Kep Nuts and C-1070-W Washers.
|
...
| KitID | 905 |
|---|
| KitDesc | Card Only - Card Ready Models |
|---|
...
Place the C-5700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
...
| KitID | 906 |
|---|
| KitDesc | Card Only - All Card Models |
|---|
...
Place the C-6700-TEMP Drill Template on the desired mounting location.
...
Verify included harnesses will reach desired location without encountering interference from internal machine components.
...
| cci-readerinstall-kit |
|---|
| KitID | 581 |
|---|
| KitDesc | ACA Controls |
|---|
|
Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly. Connect the green wire to a chassis ground. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
| Cci readerinstall kit |
|---|
| KitID | 837 |
|---|
| KitDesc | Titanium Controls |
|---|
|
Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
...
| KitID | 595 |
|---|
| KitDesc | Hybrid Coin Slides |
|---|
...
Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
...
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
...
| cci-readerinstall-kit |
|---|
| KitID | 700 |
|---|
| KitDesc | Factory Standard Coin Drop |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.
|
| Cci readerinstall kit |
|---|
| KitID | 704 |
|---|
| KitDesc | Factory Standard Coin Slide |
|---|
|
Locate the micro switch on the coin slide assembly for the upper pocket. Disconnect the harness connected to the microswitch and connect C-6253 Coin Sense Harness to the spade tabs on the micro switch.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
| KitID | 645 |
|---|
| KitDesc | Pulse - Coin Connection |
|---|
|
Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
|
| Cci readerinstall kit |
|---|
| KitID | 582 |
|---|
| KitDesc | Serial Communication / Serial Pulse |
|---|
|
Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board.
|
| Cci readerinstall kit |
|---|
| KitID | 636 |
|---|
| KitDesc | Hybrid Coin Slide Switch |
|---|
|
Connect the C-5256 Machine Start Harness to the the harness previously connected to the coin slide microswitch spade tabs.| step |
|---|
|
|
...