3333 F1 Reader Install Guide

Owned by Brett Norrell (Deactivated)
Last updated: Jan 23, 2024 by Chris Kite
2 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: LG
Make: LG
Model Length: Not Set

WiFi 2.0 controls are supported for Serial interface, but do not have support for coins at this time.

Giant-C Washer
Giant-C Plus Washer
Giant-C Pro Washer
Giant-C Fast & Wifi Washer
Titan-C Washer
Titan-C Max Washer

Associated Models

GCW1069QS
GCWF1069CD1
GCWF1069CD3
GCWF1069CS1
GCWF1069CS3
GCWF1069QS1
GCWF1069QS3
GCWF1069QS5
GCWL1069CD5
GCWL1069CS1
GCWL1069CS5
GCWL1069CS8
GCWL1069QD3
GCWL1069QD5
GCWL1069QS5
GCWM1069CD7
GCWM1069CD8
GCWM1069CS7
GCWM1069CS8
GCWM1069QD7
GCWM1069QS7
GCWP1069CD1
GCWP1069CS1
GCWP1069CS2
GCWP1069CS3
GCWP1069QS1
GCWP1069QS2
GCWP1069QS3
TCWM2013CS3

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0010

Part #: C-5801

Desc 1: F1 Reader Mounting Kit

Desc 2: Front

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

 I-M0093

Part #: C-5633-R1

Desc 1: Label - Build: TK

Desc 2: 3.5 x 1.75

   Qty: 1

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard Mounting Guide for further instructions.

  4. If needed, use C-5633-R1 Label to cover the factory card reader slot.

Connect Power

 I-P0003

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0001

Part #: C-5250

Desc 1: Coin Sense Harness

Desc 2:

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0046

Part #: C-5272

Desc 1: Machine Start Harness

Desc 2: LG

   Qty: 1

  1. Connect the C-5257 Machine Start Harness to the Coin 1 harness previously connected to the coin drop.

 I-T0047

Part #: C-5274R1

Desc 1: Machine Start Harness

Desc 2: LG

   Qty: 1

  1. Connect the C-5274R1 Machine Start Harness to the Serial connector on the communication harness.

Connect and Mount Reader

  1. Feed remaining harness ends through the mounting hole as described in the FasCard Mounting Guide.

  2. Connect the free end of the Machine Start Harness:

    1. For C-5272 pulse harness setups connect to port 2 (Pulse Connection Port) as shown in the image above.

    2. For C-5274R1 serial harness setups connect to port 1 (Serial Connection Port) as shown in the image above.

  3. Connect the free end of the C-5250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.

  4. Connect the free end of the C-5500 Power Extension Harness to port 4 ( Power Harness Connection Port) as shown in the image above.

  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO