0370 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Vending
Manufacturer: Vend-Rite
Make: Vend-Rite
Model Length: Not Set

Associated Models

ROYAL200

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-C0019

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

Part #: C-0105

Desc 1: Machine Start Harness

Desc 2: Vendrite Royal 200

   Qty: 1

Power

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Machine Interface

  1. Connect the C-0105 Machine Start Harness to the machine.

    1. Connect C-0105 Machine Start Harness bundled Blue and Red connectors.

      1. Blue connector goes to Common.

      2. Red connector goes to Normally Open.

    2. C-0105 Machine Start Harness bundled Red connectors.

      1. Red connectors go to Sel.

Connect Machine Interface Harness

Instructions do not exist for Kit I-T0070

 I-C0019

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

Part #: C-0105

Desc 1: Machine Start Harness

Desc 2: Vendrite Royal 200

   Qty: 1

Power

  1. Tap power as described in the Fascard Reader Install - Universal Concepts document using the C-5101 Spade Taps provided.

  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Machine Interface

  1. Connect the C-0105 Machine Start Harness to the machine.

    1. Connect C-0105 Machine Start Harness bundled Blue and Red connectors.

      1. Blue connector goes to Common.

      2. Red connector goes to Normally Open.

    2. C-0105 Machine Start Harness bundled Red connectors.

      1. Red connectors go to Sel.

CCI Software Configuration

Machine ControlPulseSerial

Additional Resources