0394 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: Laundrylux
Make: Wascomat
Model Length: 6

FasCard Coin & Card kit depends on how the coin drop is connected to the dryer computer.

Associated Models


TD3030
TD30x30
TD3535
TD4040
TD4545
TD45X45

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0017

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

   Qty: 1

Part #: C-5500-84

Desc 1: Power Extension Harness

Desc 2: 84"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in FasCard Reader Install - Universal Concepts by connecting the C-5101 Power Adapter Harness to the power distribution panel inside the machine.

    • 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    • 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    • Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5101 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Power

 I-P0017

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

   Qty: 1

Part #: C-5500-84

Desc 1: Power Extension Harness

Desc 2: 84"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in FasCard Reader Install - Universal Concepts by connecting the C-5101 Power Adapter Harness to the power distribution panel inside the machine.

    • 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    • 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    • Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5101 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

 I-T0014

Part #: C-0111-RES

Desc 1: Machine Start Harness

Desc 2: Two Wire Harness w/ Resistor

   Qty: 1

  1. Connect the bare wire ends of the C-0111-RES Machine Start Harness to the terminal block.

  2. Terminal block connections are numbered 0-6 from the edge nearest the top of the board (position 0) to the bottom of the terminal block (position 6)

    • For machines shipped before 1/1/2006, connect harness to positions 1 and 3.

    • For machines shipped after 1/1/2006, connect harness to positions 3 and 5.

    • For machines shipped near 6/1/2007, connect harness to positions 2 and 3.

    • All other machines, connect harness to positions 3 and 4.