0548 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Maytag
Make: Maytag
Model Length: 10

Associated Models


MFR35MCATS
MFR35MCAVS
MFR50MCATS
MFR50MCAVS

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0019

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the FasCard Reader Install - Universal Concepts document by connecting the C-5336 Power Adapter Harness to the power distribution panel inside the machine.

    • 120vac: Connect the blue wire to L1 and the brown wire to N.

    • 240vac: Connect the blue wire to L1 and the brown wire to L2.

    • Secure the green/yellow wire beneath the ground screw.

  2. Connect the opposite end of the C-5336 Power Adapter Harness to the C-5602R1 Power Converter.

  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-C0004

Part #: C-5334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Disconnect the existing wires from the Coin Drop and connect the C-5334 Combination Coin/Start Harness to the Coin Drop.

    1. Blue wires go to common (Co) and normally open (NO) on coin switch.

  2. Disconnect the existing wires from the Coin Drop.

    1. Connect the C-5334 to the Coin Drop.

    2. Connect the Violet wires to Blue wires 36 & 35.

    3. White wires wrapped with Violet go to Red wires 207 & 30.

    4. White wires wrapped with Blue go to Brown coin blocking solenoid wires.

      1. Wrap the connectors in electrical tape to keep the bare terminals from exposing.

 I-C0013

Part #: C-6334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Connect the original wires from the Coin Drop to the Violet wires.

  2. Disconnect the wires from the Coin Block solenoid and connect to the White (male) wires.

Connect Machine Interface Harness

 I-C0004

Part #: C-5334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Disconnect the existing wires from the Coin Drop and connect the C-5334 Combination Coin/Start Harness to the Coin Drop.

    1. Blue wires go to common (Co) and normally open (NO) on coin switch.

  2. Disconnect the existing wires from the Coin Drop.

    1. Connect the C-5334 to the Coin Drop.

    2. Connect the Violet wires to Blue wires 36 & 35.

    3. White wires wrapped with Violet go to Red wires 207 & 30.

    4. White wires wrapped with Blue go to Brown coin blocking solenoid wires.

      1. Wrap the connectors in electrical tape to keep the bare terminals from exposing.

 I-C0013

Part #: C-6334

Desc 1: Combination Harness

Desc 2: CGI CM

   Qty: 1

  1. Connect the Blue wires to the NC and Co terminals on the Coin Drop Micro Switch.

  2. Connect the White (female) wires to the Coin Block solenoid.