0679 Reader Install Guide
- Chris Kite
- CCI Integration User
Warning!
This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.
It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.
Overview
Equipment Details
Type: Tumble Dryer (Single)
Manufacturer: Dexter
Make: Dexter
Model Length: 22
Associated Models
DC0030NC10EC1XSWBSGUSA
DC0030NC10EC1XSWBSGUSX
DC0030NC10EC1XSWBSSUSA
DC0030NC10EC1XSWKSGUSA
DC0030NC10EC1XWWBSGUSA
DC0050NC10EC1XSWBSGUSA
DC0050NC10EC1XSWBSGUSX
DC0050NC10EC1XSWKCGUSA
DC0050NC10EC1XSWKSGUSA
DC0050NC10EC1XWWBSGUSA
DC0050NC10EC1XWWKSGUSA
DC0050NC15EC1XSWKCGUSA
DC0050NC15EC2XSWBSGUSX
DC0080NC10EC1XSWBCGUSA
DC0080NC10EC1XSWBCGUSX
DC0080NC10EC1XSWBCSUSA
DC0080NC10EC1XSWBSGUSA
DC0080NC10EC1XSWBSGUSX
DC0080NC10EC1XSWBSSUSX
DC0080NC10EC1XSWKCGUSA
DC0080NC10EC1XSWKCGUSX
DC0080NC10EC1XSWKCSUSA
DC0080NC10EC1XSWKCSUSX
DC0080NC10EC1XSWKSGUSA
DC0080NC10EC1XSWKSGUSX
DC0080NC10EC1XSWKSSUSA
DC0080NC10EC1XSWKSSUSX
DC0080NC10EC1XWWBSGUSA
DC0080NC10EC1XWWBSGUSX
DC0080NC10EC1XWWKSGUSA
DC0080NC10EC1XWWKSGUSX
DC0080NC10EC2RSWKCSUSX
DC0080NC10EC2RSWKSGUSX
DC0080NC10EC2RSWKSSUSX
DC0080NC10EC2RWWBSSUSX
DC0080NC10EC4XSWBSGUSX
DC0120NC10EC1XSWKSGUSA
DC0120NE10EC2RSWBCGUSA
DC0120NE10EC2RSWBCGUSX
DC0120NE10EC2RSWBSGUSA
DC0120NE10EC2RSWBSGUSX
DC0120NE10EC2RSWBSSUSA
DC0120NE10EC2RSWKCGUSA
DC0120NE10EC2RSWKCGUSX
DC0120NE10EC2RSWKCSUSA
DC0120NE10EC2RSWKCSUSX
DC0120NE10EC2RSWKSGUSA
DC0120NE10EC2RSWKSSUSA
DC0120NE10EC2RWWBSGUSA
Recommended Tools and Supplies
Drill
1 1/8" Tungsten Carbide Tipped Hole Cutter
Cutting Oil
9/64" Drill Bit
Center Punch
Hammer
Fine Point Permanent Marker
Pliers
Tape Measure
Installation
Connect Power
Part #: C-5211
Desc 1: Power Adapter Harness
Desc 2: CGI - AC
Qty: 1
Part #: C-5500-60
Desc 1: Power Extension Harness
Desc 2: 60"
Qty: 1
Part #: C-5602R1
Desc 1: Power Converter
Desc 2: SMT-012-018VW
Qty: 1
Tap power as described in the Fascard Reader Install - Universal Concepts document by connecting the C-5211 Power Adapter Harness to the power distribution panel inside the machine.
120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.
240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.
Secure the green wire beneath the ground screw.
Connect the opposite end of the C-5211 Power Adapter Harness to the C-5602 Power Converter.
Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Part #: C-5256
Desc 1: Machine Start Harns (pulse)
Desc 2: 20" - Male taps, Rq. Female
Qty: 1
Connect the C-5256 Machine Start Harness to the Yellow/Black and Yellow/Red wires coming from the P3 connection on the Machine Control Assembly.
