0863 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer
Manufacturer: Alliance
Make: IPSO
Model Length: 4

Associated Models


HW94

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0012

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 3

Part #: C-5210

Desc 1: Power Adapter Harness

Desc 2: CGI

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap the machine AC power wires using the C-5101 Spade Taps. See FasCard Reader Install - Universal Concepts for more details.

    1. For 120vac models: L1, N, and Ground wires

    2. For 240vac models: L1, L2, and Ground wires

  2. Connect the three wires from the C-5210 Power Adapter Harness to the C-5101 Spade Taps.

    1. Connect the Blue wire to the L1 tap.

    2. Connect the Brown wire to the N/L2 tap.

    3. Connect the Green/Yellow wire to the Ground tap.

  3. Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connector on the C-5602R1 Power Converter.

  4. Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connector on the C-5500-60 Power Extension Harness.

  5. Run the C-5500-60 Power Extension Harness to the reader mounting location.

Connect Coin Sense Harness

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the factory harness from the micro switch tabs on the Coin Drop.

  2. Connect the C-6253 Coin Sense Harness to the micro switch tabs in any pairing.

Connect Machine Interface Harness

 I-T0016

Part #: C-0113

Desc 1: Machine Start Harness

Desc 2: 2-Wire Harness

   Qty: 1

  1. Remove the harness connected to the microswitch mounted to the coin drop. Connect the C-0113 Machine Start Harness to the harness previously connected to the microswitch.

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the micro switch on the coin drop/slide.

Fascard Admin Site Configuration

Use the following settings depending on the Machine Start Harness used.

Pulse (C-5256)

  1. Equipment Type: SingleVend

  2. Pulse Length: 500

CCI Software Configuration

Machine ControlPulseSerial
Micro 20SingleVend (Relay) / 500ms*NOT SUPPORTED*

Additional Resources