2073 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Vending
Manufacturer: Royal Vendors
Make: Royal Vendors
Model Length: Not Set

Associated Models

RVCE65410
RVDVE65010

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Install Mounting Hardware

 I-M0037

Part #: C-0014S

Desc 1: Label

Desc 2: TD LC Window

   Qty: 1

Part #: C-0015S

Desc 1: Label

Desc 2: TD30 Insert Card Graphic

   Qty: 1

Part #: C-0974

Desc 1: Flat Mount Bezel

Desc 2: Fits 3-1/2" x 4-1/4" Opening

   Qty: 1

Part #: C-1042

Desc 1: Nut

Desc 2: 8-32 - Kep

   Qty: 4

  1. Remove payment device bay cover plate if still installed.

  2. Take LaundryCard Reader and remove the front bezel by unscrewing the four screws around the card slot.

  3. Attach the LaundryCard Reader to the C-0974 Flat Mount Bezel using the previously removed screws.

  4. Install C-0974 Flat Mount Bezel into the Payment Device Bay and secure using the C-1042 Kep Nuts.

  5. Apply the C-0014S Window Label over the display opening of the C-0974 Flat Mount Bezel.

  6. Apply the C-0015S Insert Card Label over the card slot opening of the C-0974 Flat Mount Bezel.

 I-M0174

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to FasCard F2/F3 Reader Installation Guide - Front Mount for further instructions.

Instructions do not exist for Kit I-M0270

Connect Power

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the male, 6-pin connector from the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

  2. Optional (FasCard Only): Use the female, 6-pin pigtail connector from the C-6124-MDB to reconnect any existing payment devices.

Power is supplied through the same Machine Interface Harness described in step 4.

Connect Coin Sense Harness

No COIN SENSE kits exist for this equipment.

Not applicable in this setup. FasCard reader does not collect payment from any other devices, and will only send funds to the machine's control.

Connect Machine Interface Harness

 I-T0071

Part #: C-0124-MLV

Desc 1: Machine Start Harness

Desc 2: MDB Communication

   Qty: 1

  1. Connect the C-0124-MLV Machine Start Harness to the MDB connector on the Machine Control Assembly.

  2. FasCard Only: Use the pigtail connection to reconnect existing devices.

 I-C0020

Part #: C-6124-MDB

Desc 1: Machine Start Harness

Desc 2: F2 MDB Interface Harness

   Qty: 1

  1. Connect the male, 6-pin connector from the C-6124-MDB Machine Start Harness to the MDB connection on the Machine Control Assembly.

  2. Optional (FasCard Only): Use the female, 6-pin pigtail connector from the C-6124-MDB to reconnect any existing payment devices.

CCI Software Configuration

Machine ControlPulseSerial
MDB*NOT SUPPORTED*Vending - MDB Level 1

Additional Resources