3552 Reader Install Guide

ERROR: Equipment ID 3552 does not exist.

Install Mounting Hardware

I-M0003

Part #: C-6801

Desc 1: F2 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to F2 FasCard Reader Mounting Guide for further instructions.

I-M0125

Part #: C-0144

Desc 1: Screw

Desc 2: 8-32 x 2" - Flat

Qty: 2

Part #: C-5365

Desc 1: Bypass Harness

Desc 2: Alliance Coin Vault Bypass

Qty: 1

Part #: C-6601

Desc 1: Spacer

Desc 2: F2 Dexter Vault Filler Plate

Qty: 1

Part #: C-6602-V2

Desc 1: F2, Large Vault Mount

Desc 2: Modified version

Qty: 1

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Part #: C-5033

Desc 1: Label

Desc 2: 4-5/8" x 3-1/2"

Qty: 1

Remove existing coin box.
Remove Vault Switch and bridge the wires previously connected to the Vault Switch with the C-5365 Bypass Harness.
Bend the side tabs of the C-6602 Vault Bracket outward and install into the coin vault. The tabs should snap into place securing the bracket.
Before securing the reader to the machine with C-0144 Screws, place the C-0906 Spacer between the reader and machine so the Screws pass through the circular holes in the Spacer.

I-M0127

Part #: C-1060

Desc 1: Screw - Build: TK

Desc 2: 8-32 x 3/8" - Zinc

Qty: 2

Part #: C-6801

Desc 1: F2 Reader Mounting Kit

Desc 2: Universal

Qty: 1

Part #: C-6970R1

Desc 1: F2, Bracket (revised)

Desc 2: Alliance Card Ready

Qty: 1

Install the C-6970 Alliance Mounting Bracket into the opening on the control panel for mounting card readers and coin drops.
Attach the C-5414 F2 Mounting Bracket to the C-6970 Alliance Mounting Bracket and secure using the C-1060 Screws.
Refer to F2 FasCard Reader Mounting Guide for further instructions.

Connect Power

I-P0002

Part #: C-6204-40

Desc 1: Power Adapter Harness

Desc 2: F2, 12vDC Pow Harness - 40"

Qty: 1

Connect the C-6204-40 Power Adapter Harness (12VDC power) to the H10 connection on the Machine Control Assembly.
1. Secure the green wire beneath the ground screw.

Connect Coin Sense Harness

I-S0027

Part #: C-6250

Desc 1: Coin Sense Harness

Desc 2: F2

Qty: 1

Disconnect the coin drop from the machine control assembly.
Connect the C-6250 Coin Sense Harness to the harness connected to the coin drop.

Connect Machine Interface Harness

I-T0003

Part #: C-5240

Desc 1: Machine Start Harness

Desc 2: Alliance ACA

Qty: 1

Connect the C-5240 Machine Start Harness to the H3 connector on the Machine Control Assembly.

Connect and Mount Reader

Item No.	Component	Notes
1	Power Connection Port	Utilizes the same power harnesses as the first generation FasCard reader.
2	Pulse Connection Port	Connection point for pulse machine start harnesses.
3	Coin 1 Connection Port	This is the connection point for the harness input associated with Coin 1.
4	Coin 2 Connection Port	This is the connection point for the harness input associated with Coin 2.
5	Serial Connection Port	This is the connection point for serial machine start harnesses.

Feed remaining harness ends through mounting hole as described in F2/F3 FasCard Reader Mounting Guide.
Connect the free end of the C-5240 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin 1 Sense Harness Connection Port) as shown in the image above.
Connect the free end of the C-6204-40 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
Connect FasCard reader to base as described in the F2/F3 FasCard Reader Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on the Machine Control Board to be set to the 'ON' position. Leave all other dip switches as is.