3638 Reader Install Guide

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Alliance
Make: Huebsch
Model Length: 18

Associated Models

HYT020VCAHXUB0C0BA
HYT020VX0HXUB0C0BA
HYT020VX0HXUB0C0FQ
HYT030VCAHXUB0C0BA
HYT030VX0HXUB0C0BA
HYT030VX0HXUB0C0FQ
HYT030VX0HXUB0X0BA
HYT040VCAHXUB0C0BA
HYT040VCAHXUB0E0BA
HYT040VX0HXUB0E0FQ
HYT055VCAHXUB0E0BA
HYT055VCAHXUB0X0BA
HYT055VX0HXUB0E0BA
HYT055VX0HXUB0E0FQ
HYT070VCAHXUB0C0BA
HYT070VCAHXUB0E0BA
HYT070VX0HXUB0E0FQ
SYT020VCAHXUB0C0BA
SYT020VX0HXUB0C0BA
SYT030VCAHXUB0C0FQ
SYT040VCAHXUB0E0BA
SYT040VX0HXUB0E0BA
SYT055VX0HXUB0E0BA

Recommended Tools and Supplies

Drill
1 1/8" Tungsten Carbide Tipped Hole Cutter
Cutting Oil
9/64" Drill Bit
Center Punch
Hammer
Fine Point Permanent Marker
Pliers
Tape Measure

Installation

Connect Coin Sense Harness

I-S0018

Part #: C-5360

Desc 1: Coin Sense Harness

Desc 2: Female taps, Rq. Male

Qty: 1

Disconnect the terminal quick connects from the terminal block mounted on top of the coin vault.
1. Mark the outer green and red quick connects for later use if using C-5265 Machine Start Harness.
Connect the C-5360 Coin Sense Harness to the terminal block tabs. Match each connection by color of the coin sensor wires.

I-S0046

Part #: C-6360

Desc 1: Coin Sense Harness

Desc 2: Female taps, Rq. Male

Qty: 1

Disconnect the terminal quick connects from the terminal block mounted on top of the coin vault.
1. Mark the outer green and red quick connects for later use if using C-5265 Machine Start Harness.
Connect the C-6360 Coin Sense Harness to the terminal block tabs. Match each connection by color of the coin sensor wires.

Machine Configuration

Singlevend - Coin Pulse

Enter the machine's System Menu and set the following settings (See machine programming manual for more info.)
1. Machine Settings
  1. Liquid Soap Supply: Enabled
2. Payment Settings:
  1. Enable Types: Disable all payment types
  2. Coin Options: Single
  3. Coin 1 Value: Intended Vend Price
  4. Coin 2 Value: Intended Vend Price
  5. Serial Payment System: Disabled
On the FasCard Admin site, create a SingleVend equipment type with the following settings:
1. Mode: Simple
2. Pulse Length: 1000
3. Pulse Interval: 250
4. Pulse Type: Relay
5. Sensor Input: Required Off
6. Show Remaining Time: Disabled
7. Cycle Time: 600 Seconds
8. # Pulses: 1