Versions Compared

Version Old Version 2 New Version 3
Changes made by

Chris Kite

CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID932
KitDescCard Only - 30lb & Smaller Models

  1. Remove existing coin box and coin drop.

  2. Attach the C-5414 Standard Mounting Bracket to theC-6922 Mounting Bracket using the (2) C-542010-32 x 1/4" Philips Screws.

  3. Install the C-6922 Mounting Bracket into the coin vault opening. Secure in place using the (2) C-1059 10-32 Keps Nuts.

Cci readerinstall kit
KitID869
KitDescCard Only - 40lb+ Models

  1. Remove existing coin box and coin drop.

  2. Attach the C-5414 Standard Mounting Bracket to theC-6920R1Mounting Bracket using the (2) C-542010-32 x 1/4" Philips Screws.

  3. Install the C-6920R1 Mounting Bracket into the coin vault opening. Secure in place using the (2) C-1059 10-32 Keps Nuts.

Connect Power

Cci readerinstall kit
KitID595
KitDescTap Source Machine Power

  1. Tap power as described in the document by connecting theC-5210Power Adapter Harnessto the power distribution panel inside the machine.

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of theC-5210Power Adapter Harnessto theC-5602R1Power Converter.

  3. Connect theC-5500Power Extension Harness to the appropriate connector on theC-5602R1Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID716
KitDescFactory - Optical Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect theC-6357 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID655
KitDescPulse - Coin
  1. Connect theC-5353R1 Machine Start Harness to theCoin 1 connector on the Machine Control Assembly.
Cci readerinstall kit
KitID814
KitDescSerial - Compass Control
  1. Connect theC-0126-MLVMachine Start Harness to the RS-232 port on the Machine Control Assembly.
  2. Connect theC-5359Machine Start Harness to the Input 1 port on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. ("Pulse - Coin" Installation Only) Connect the free end of theC-5353R1 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. ("Serial - Compass Control" Installation Only) Connect the free end of the C-0126-MLV Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
    1. Connect the free end of theC-5359 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  4. (Coin and Card Installation Only) Connect the free end of the C-6357 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
Cci readerinstall footer