Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID906
KitDescCard Only - Card Models
  1. Insert the factory block-out plate into the coin vault opening and/or insert the blank plate into the coin-meter aperture opening.
  2. Place the C-6700-TEMP Drill Templateon the desired mounting location.
    1. Suggested locations to mount:
      1. Dryer: (a.)alternate mounting location to the left of the control panel;(b.)coin-meter aperture opening with blank plate;(c.)coin vault opening (If factory block-out plate is installed.).
      3. Washer: (a.)coin-meter aperture opening with blank plate;(b.)coin vault opening (If factory block-out plate is installed.).
  3. Mark hole"C"for the pilot hole of the primary mounting point.
    1. Optional: Mark"D"and"E"holes to provide additional support for the reader and ensure minimal "play" on card reader bracket position (Requires additional fasteners. Not supplied by CCI.)
  4. Use a1-1/8" hole sawto drill a hole at position"C".
  5. Place and align C-5414Mounting Bracketso that the center hole aligns with hole "C".
  6. Align the center hole of theC-5414Mounting Bracketto the newly drilled hole on the machine face.
  7. Slip theC-5702Chase Nipplethrough the hole and secure with theC-5703Locknut.
    1. Tighten the chase nipple to prevent the bracket from rotating.
    2. Screws may be inserted through the smaller holes provided on the bracket and secured to the mounting face, if desired.

Connect Power

Cci readerinstall kit
KitID595
KitDescTap Machine Power - Washer & Dryer
  1. Tap the incoming AC power wires using theC-5101Spade Taps.
    1. For120vmodels:L1,N, andGroundwires
    2. For240/208vmodels:L1,L2, andGroundwires
  2. Connect the three wires from the C-5210 Power Adapter Harnessto theC-5101 Spade Taps.
    1. Connect theBluewire to the L1tap.
    2. Connect the Brownwire to the N/L2tap.
    3. Connect theGreen/Yellowwire to the Groundtap.
  3. Connect the 3-pinconnector from the C-5210 Power Adapter Harnessto the matching connector on the C-5602R1 Power Converter.
  4. Connect the 4-pinconnector from theC-5602R1 Power Converterto the matching connector on theC-5500Power Extension Harness.
  5. Run the C-5500Power Extension Harness to the reader mounting location.

Connect Machine Interface Harness

Cci readerinstall kit
KitID658
KitDescSerial Communication and Pulse Connection
  1. Connect the C-5355 Machine Start Harnessto theCN4 Payment-Device Connection.
  2. Run the C-5355 Machine Start Harnessto the reader mounting location.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptcom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. Connect the free end of the C-5355 Machine Start Harness to port 5 (Serial Connection Port) as shown in the image above.
  3. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Washer -

Multiexcerpt include
SpaceWithExcerptcom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
MultiExcerptNameEncore - FLW
PageWithExcerpt_Machine Configuration

Cci readerinstall footer