Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID866
KitDescCard Only
  1. Remove coin dropand install C-0900Drop Cover.
    1. Secure using the (4) C-1013 6-32 Keps Nuts.
  2. Spread the C-6936 Vault Mount Bracket wings outward before insertion to lock bracket into place.
  3. Insert the C-6936 Vault Mount Bracket into the coin vault.
  4. Secure the C-5414 F2 Mounting Bracketto the C-6936 Vault Mount Bracket with the (2) C-0144 8-32 x 2" Screws.

Connect Power

Cci readerinstall kit
KitID595
KitDescTap Machine Power
  1. Tap power as described in the document using theC-5101 Spade Taps provided.
  2. Connect theC-5210 Power Adapter Harnessto the installed spade taps.
  3. Connect theC-5210 Power Adapter Harness to theC-5602 Power Converter.
  4. Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.
  5. Connect the opposite end of theC-5210 Power Adapter Harnessto theC-5602 Power Converter.
  6. Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID886
KitDescCoin Drop: Coin Micro
  1. Disconnect the existing wires from the Coin Drop and connect the C-6334 Combination Coin/Start Harness to the Coin Drop.
    1. Blue wires go to common (Co) and normally open (NO) on coin switch.
Cci readerinstall kit
KitID888
KitDescCoin Drop: Coin Rotary
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6335 Combination Harness (3-pin, black connector) to the Coin Eye Sensor.
    1. The White wire (female) spade connectors bundled with the black connector attach to theCoin Blocksolenoid.

Connect Machine Interface Harness

Cci readerinstall kit
KitID886
KitDescPulse - Coin Micro
  1. Disconnect the existing wires from the Coin Drop.
    1. Connect the C-6334 Machine Start Harness to the Coin Drop.
    2. Connect the Violet wires to Blue wires 36 & 35.
    3. White wires wrapped with Violet go to Red wires 207 & 30.
    4. White wires wrapped with Blue go to Brown coin blocking solenoid wires.
      1. Wrap the connectors in electrical tape to keep the bare terminals from exposing.
Cci readerinstall kit
KitID888
KitDescPulse - Coin Rotary
  1. Connect the Violet wire (male) spade connectors to theCoin Sense Input.
  2. Connect the remaining White wire (male) spade connectors to theCoin Blocksolenoid drive.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting holes.
  2. Connect the white, 6 pin connector from the C-6334 or C-6335 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. (Coin and Card Installations Only) Connect the white, 5 pin connector from the C-6334 or C-6335 Machine Start Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the F2/F3 Reader Mounting Guide.
Cci readerinstall footer