Versions Compared

Version Old Version 2 New Version 3
Changes made by

Chris Kite

CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID584
KitDescCoin and Card

  1. Place theC-6700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID857
KitDescCard Only - 10° Panel Coin Models

  1. Remove existing coin box and coin drop.

  2. Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Attach theC-5414 F2 Mounting Bracketto the C-6765-W-R1 Metercase Bracketusing (2) C-5420 10-32 x 1/4 Pan Screws.
  4. Run any card reader harnesses through the coin slot openings and the circular hole in theC-6765-W-R1Metercase Bracket.

  5. Install the C-6765-W-R1Metercase Bracketso that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nutsand (2) C-1070-WWashers.

Cci readerinstall kit
KitID911
KitDescCard Only - Flat Front Panel Coin Models

  1. Remove existing coin box and coin drop.

  2. Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
  3. Bend the tabs outward and insert theC-0940 Vault Cover in to the coin vault opening.
  4. Apply the C-5035 Label over the opening for the coin drop.

  5. Place theC-6700-TEMPDrill Template on the desired mounting location.

  6. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  7. Refer to for further instructions.

Cci readerinstall kit
KitID906
KitDescCard Only - Card Models

  1. Place theC-6700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Connect Power

Cci readerinstall kit
KitID581
KitDescACA Controls
  1. Connect theC-6204-40 12VDC Power Harnessto theH10connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Cci readerinstall kit
KitID837
KitDescTitanium Controls
  1. Connect the 2-pin connector from theC-6207 F2, ACA Power Harnessto the 24v transformer behind the front control panel.
  2. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
Cci readerinstall kit
KitID794
KitDescACA Controls with Electronic Coin Drops
  1. Tap power as described in the document using the C-5101 Spade Taps provided.
  2. Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602R1 Power Converter.
  3. Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID700
KitDescFactory Optical Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect theC-6250 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID648
KitDescPulse - Coin
  1. Connect theC-5300-NC Machine Start Harness to the coin 1 connector on the Machine Control Assembly.
Cci readerinstall kit
KitID582
KitDescSerial Communication / Serial Pulse
  1. Connect theC-5240 Machine Start Harness to the the H3connection on the Machine Control Assembly or Communication board.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole.
  2. (Pulse - Coin Only) If using theC-5300-NCMachine Start Harness, connect the free end to port 2 (Pulse Connection Port) as shown in the image above.
  3. (Serial Comm Only) If using theC-5240Machine Start Harness, connect the free end to port 5 (Serial Connection Port) as shown in the image above.
  4. (Coin and Card Installations Only) Connect the free end of theC-6250Coin Sense Harnessto port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  5. Connect the free end of the C-6204-40, C-6207, or C-5500-84 Power Harnessto port 1 (Power Harness Connection Port) as shown in the image above.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameACA Configuration
PageWithExcerpt_Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameTitanium Configuration (FLW/Small Dryer)
PageWithExcerpt_Machine Configuration

Cci readerinstall footer