Versions Compared

Old Version 2

changes.mady.by.user Chris Kite

Saved on

compared with

New Version 3

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID841
KitDescCoin and Card

  1. Place the C-6700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID840
KitDescCard Only
  1. Feed the harness ends through thecoin vault opening and then through the circular opening in theC-6602Vault Mount Bracket.
  2. Spread theC-6602Vault Mount Bracketwings outward and then insert theC-6602Vault Mount Bracketinto thecoin vault.
  3. Feed the harness ends through the C-5414 F2 Mounting Bracket and C-6601 Spacer Plate.
  4. Secure theC-5414F2 Mounting Bracketto theC-6939 Vault Mount Bracket with theC-0144Screws.
  5. Install theC-5710 Rubber Grommetinto the circular opening of the C-5414 F2 Mounting Bracket and C-6601 Spacer Plate.
  6. Remove any existing coin drop.
  7. Mount the C-0905 Drop Cover using existing mounting hardware where the coin drop was previously installed.

Connect Power

Cci readerinstall kit
KitID805
  1. Tap power as described in the document by connecting theC-5211 Power Adapter Harness to the male spade connectors on the machine power panel.
    1. Connect the green wire to the ground terminal.
    2. A corner of the power panel cover may need to be bent slightly to allow the power harness egress.
  2. Connect the opposite end of theC-5211 Power Adapter Harness to the C-5602 Power Converter.
  3. Connect theC-5500-60 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID704
KitDescCoin Drop: Factory
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID636
KitDescPulse
  1. Connect theC-5256 Machine Start Harness to the Coin Drop Harness previously connected to the coin drop.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF2 Reader
PageWithExcerpt_Reader Ports

Item No.ComponentNotes
1Power Connection PortUtilizes the same power harnesses as the first generation FasCard reader.
2Pulse Connection PortConnection point for pulse machine start harnesses.
3Coin 1 Connection PortThis is the connection point for the harness input associated with Coin 1.
4Coin 2 Connection PortThis is the connection point for the harness input associated with Coin 2.
5Serial Connection PortThis is the connection point for serial machine start harnesses.
  1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
  2. Connect the free end of the C-5256 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500-60 Power Harness to port 1.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

TODO

Cci readerinstall footer