0587 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Dryer
Manufacturer: Dexter
Make: Dexter
Model Length: Not Set

Associated Models


DCBD30KCS
DCBD30KCW10US
DCBD30KCX
DCBD80KCW10CN
DCBD80KCW10US
DCBD80KCX

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0015

Part #: C-5211

Desc 1: Power Adapter Harness

Desc 2: CGI - AC

   Qty: 1

Part #: C-5500-60

Desc 1: Power Extension Harness

Desc 2: 60"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Tap power as described in the FasCard Reader Install - Universal Concepts document by connecting the C-5211 Power Adapter Harness to the male spade connectors on the machine power panel.

    1. Connect the green wire to the ground terminal.

    2. A corner of the power panel cover may need to be bent slightly to allow the power harness egress.

  2. Connect the opposite end of the C-5211 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500-60 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

 I-S0004

Part #: C-5253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5253 Coin Sense Harness to the harness connected to the Coin Drop.

 I-S0031

Part #: C-6253

Desc 1: Coin Sense Harness

Desc 2: 28"

   Qty: 1

  1. Disconnect the factory harness from the micro switch tabs on the Coin Drop.

  2. Connect the C-6253 Coin Sense Harness to the micro switch tabs in any pairing.

Connect Machine Interface Harness

 I-T0016

Part #: C-0113

Desc 1: Machine Start Harness

Desc 2: 2-Wire Harness

   Qty: 1

  1. Remove the harness connected to the microswitch mounted to the coin drop. Connect the C-0113 Machine Start Harness to the harness previously connected to the microswitch.

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the micro switch on the coin drop/slide.

CCI Software Configuration

Machine ControlPulseSerial
A-Series (1.0)SingleVend (Relay) / 55ms*NOT SUPPORTED*

Additional Resources