Place the C-5700-TEMPDrill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.
Cci readerinstall kit
KitID
962
KitDesc
Card Only
Remove coin drop and install C-0900Drop Cover.
Secure with C-1013Nut.
Spread the C-0936Vault Mount Bracket wings outward before insertion to lock bracket into place.
Insert the C-0936Vault Mount Bracket into the coin vault.
Attach C-0134 Standoffs to the C-0936Vault Mount Bracket.
Secure reader to the C-0936 Vault Mount Bracket using C-0146 Screws.
Cci readerinstall kit
KitID
584
KitDesc
Coin and Card
Place the C-6700-TEMPDrill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guidefor further instructions.
Cci readerinstall kit
KitID
866
KitDesc
Card Only
Remove
coin
coin drop and install C-0900Drop Cover.
Secure using the (4)C-10136-32 Keps Nuts.
Spread the C-6936Vault Mount Bracket wings outward before insertion to lock bracket into place.
Insert the C-6936Vault Mount Bracket into the coin vault.
Secure the C-5414F2 Mounting Bracketto the C-6936Vault Mount Bracket with the (2) C-01448-32 x 2" Screws.
Connect Power
Cci readerinstall kit
KitID
595
KitDesc
Tap Machine Power
Tap power as described in the Fascard Reader Install - Universal Conceptsdocument using the C-5101 Spade Taps provided.
Connect the C-5210 Power Adapter Harness to the installed spade taps.
Connect the C-5210 Power Adapter Harness to the C-5602 Power Converter.
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Connect the opposite end of the C-5210 Power Adapter Harness to the C-5602 Power Converter.
Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
Connect Coin Sense Harness
Cci readerinstall kit
KitID
877
KitDesc
Coin Drop: Coin Micro
Disconnect the existing wires from the Coin Drop and connect the C-5334Combination Coin/Start Harness to the Coin Drop.
Blue wires go to common (Co) and normally open (NO) on coin switch.
Cci readerinstall kit
KitID
879
KitDesc
Coin Drop: Coin Rotary
Disconnect the Coin Drop from the Machine Control Assembly.
Connect the C-5335Combination Harness (3-pin, black connector) to the Coin Eye Sensor.
The White wire (female) spade connectors bundled with the black connector attach to the Coin Block solenoid.
Cci readerinstall kit
KitID
886
KitDesc
Coin Drop: Coin Micro
Disconnect the existing wires from the Coin Drop and connect the C-6334Combination Coin/Start Harness to the Coin Drop.
Blue wires go to common (Co) and normally open (NO) on coin switch.
Cci readerinstall kit
KitID
888
KitDesc
Coin Drop: Coin Rotary
Disconnect the Coin Drop from the Machine Control Assembly.
Connect the C-6335Combination Harness (3-pin, black connector) to the Coin Eye Sensor.
The White wire (female) spade connectors bundled with the black connector attach to the Coin Block solenoid.
Connect Machine Interface Harness
Cci readerinstall kit
KitID
886877
KitDesc
Pulse - Coin Micro
Disconnect the existing wires from the Coin Drop.
Connect the C-
6334 Machine Start Harness
5334to the Coin Drop.
Connect the Violet wires to Blue wires 36 & 35.
White wires wrapped with Violet go to Red wires 207 & 30.
White wires wrapped with Blue go to Brown coin blocking solenoid wires.
Wrap the connectors in electrical tape to keep the bare terminals from exposing.
Cci readerinstall kit
KitID
888879
KitDesc
Pulse - Coin Rotary
Connect the Violet wire (male) spade connectors to the Coin Sense Input.
Connect the remaining White wire (male) spade connectors to the Coin Block solenoid drive.
Connect and Mount Reader
Multiexcerpt include
SpaceWithExcerpt
CCIDOC
MultiExcerptName
F2 Reader
PageWithExcerpt
_Reader Ports
...
Cci readerinstall kit
KitID
886
KitDesc
Pulse - Coin Micro
Disconnect the existing wires from the Coin Drop.
Connect the C-6334 Machine Start Harness to the Coin Drop.
Connect the Violet wires to Blue wires 36 & 35.
White wires wrapped with Violet go to Red wires 207 & 30.
White wires wrapped with Blue go to Brown coin blocking solenoid wires.
Wrap the connectors in electrical tape to keep the bare terminals from exposing.
Cci readerinstall kit
KitID
888
KitDesc
Pulse - Coin Rotary
Connect the Violet wire (male) spade connectors to the Coin Sense Input.
Connect the remaining White wire (male) spade connectors to the Coin Block solenoid drive.