Versions Compared

Old Version 10

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version 11

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID591
KitDescCoin and Card

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 Reader Mounting Guide for further instructions.

  • Remove the mounting bolt securing the coin drop to the metercase. Then remove the coin drop and coin box.

  • Run reader harnesses through the metercase and the hole on the C-5771 Metercase Bracket.

    • Install C-5771Metercase Bracketinto the metercase and secure using C-0303 Mounting Bolt.
    Cci readerinstall kit
    KitID813KitDescCard Only - Coin Model
    Cci readerinstall kit
    KitID904
    KitDescCard Only - Card Model

    1. Remove the (4) security torx retaining screws on the front of the machine.

    2. Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.

    3. Locate and remove the (2) security torx screws inside the soap tray opening.

    4. Remove the final (2) torx screws to open the top cover.

    5. Locate a spot on top of the machine to mount the reader. Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-5700-TEMP Drill Template.

    6. Refer to F1 Reader Mounting Guide for instructions on drilling mounting holes and mounting the reader.

    Connect Power

    Cci readerinstall kit
    KitID663
    KitDescTap Machine Power

    1. Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.

    2. Use the C-5101 Spade Taps to tap the black (L1) and white (Neutral) wires.

    3. Attach the spade ends of the C-5336 Power Adapter Harness to the taps. Blue to black, and Brown to White.

    4. Attach the Green ground wire from the C-5336 Power Adapter Harness to a nearby chassis ground screw.

    5. Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.

    6. Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500 Power Extension Harness.

    7. Mount the C-5602R1Power Converter in the machine by using zip ties to secure it to the machine's wire harness.

    Connect Coin Sense Harness

    Cci readerinstall kit
    KitID693
    KitDescFactory - Optical Coin Drop

    1. Disconnect the Coin Drop from the Machine Control Assembly.

    2. Connect the C-5362 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID1004
    KitDescPulse - AA3 / Debit Connection

    1. Connect the C-5364 Machine Start Harness to the AA3 connector on the Machine Control Assembly.

      1. If needed, use the C-0126-MLV-EXT15 Extension Harness to extend

    the C-5364 Machine Start Harness.

    Connect and Mount Reader

    Image Removed

    ...

      1. the

    ...

      1. C-5364 Machine Start

    ...

      1. Harness

    ...

      1. .

    Machine Configuration

    1. Enter Service Mode and navigate to J option.

    2. Set option to J.d.

    3. Exit Service Mode.

    ...