Skip to end of banner
Go to start of banner

3670 F1 Reader Install Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 11 Next »

Install Mounting Hardware

 I-M0006

Part #: C-5014

Desc 1: Reader Base & Gasket

Desc 2: F1

   Qty: 1

Part #: C-5027

Desc 1: Label

Desc 2: Credit Card Logo

   Qty: 1

Part #: C-5702

Desc 1: Chase Nipple

Desc 2: 3/4"

   Qty: 1

Part #: C-5703

Desc 1: Lock Nut

Desc 2: 3/4" - 102-S

   Qty: 1

Part #: C-5705

Desc 1: Screw

Desc 2: 8 x 1-1/2 Plastite

   Qty: 2

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to F1 Reader Mounting Guide for further instructions.

 I-M0134

Part #: C-5800

Desc 1: F1 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

  1. Remove the (4) security torx retaining screws on the front of the machine.

  2. Remove the soap tray by pulling it out and pressing on the retaining tab in the rear of the tray.

  3. Locate and remove the (2) security torx screws inside the soap tray opening.

  4. Remove the final (2) torx screws to open the top cover.

  5. Locate a spot on top of the machine to mount the reader. Verify included harnesses will reach desired location without encountering interference from internal machine components. Mark the location using C-5700-TEMP Drill Template.

  6. Refer to F1 Reader Mounting Guide for instructions on drilling mounting holes and mounting the reader.

Connect Power

 I-P0007

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Locate the incoming power cables in the rear of the machine. This should include a white, black and green wire.

  2. Use the C-5101 Spade Taps to tap the black (L1) and white (Neutral) wires.

  3. Attach the spade ends of the C-5336 Power Adapter Harness to the taps. Blue to black, and Brown to White.

  4. Attach the Green ground wire from the C-5336 Power Adapter Harness to a nearby chassis ground screw.

  5. Connect the 3-pin connector from the C-5336 Power Adapter Harness to the 3-pin connector on the C-5602R1 Power Converter.

  6. Connect the 4-pin connector from the C-5602R1 Power Converter to the 4-pin connector on the C-5500 Power Extension Harness.

  7. Mount the C-5602R1 Power Converter in the machine by using zip ties to secure it to the machine's wire harness.

Connect Coin Sense Harness

 I-S0020

Part #: C-5362

Desc 1: Coin Sense Harness

Desc 2: MLG

   Qty: 1

  1. Disconnect the Coin Drop from the Machine Control Assembly.

  2. Connect the C-5362 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

 I-T0090

Part #: C-5364

Desc 1: Machine Start Harness

Desc 2: Maytag MFR

   Qty: 1

Part #: C-0126-MLV-EXT15

Desc 1: Extension Harness

Desc 2: Compass

   Qty: 1

  1. Connect the C-5364 Machine Start Harness to the AA3 connector on the Machine Control Assembly.

    1. If needed, use the C-0126-MLV-EXT15 Extension Harness to extend the C-5364 Machine Start Harness.

Machine Configuration

  1. Enter Service Mode and navigate to J option.

  2. Set option to J.d.

  3. Exit Service Mode.

  • No labels