Versions Compared

Old Version 6

changes.mady.by.user Former user

Saved on

compared with

New Version 7

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Div
Classtoc-header
Section
Column
width30
Panel
titleOn this Page

Table of Contents
maxLevel2
minLevel2

Column
width70
Paneltitle

Overview

This page is intended to guide the user through the replacement of the local card reader on the X-Changer cabinet.

Multiexcerpt include
MultiExcerptNameWarning
DisableCachingtrue
PageWithExcerptCCIDOC:_General

Recommended Tools and Supplies (Not Included)

No.2 Phillips Screwdriver
(Or Equivalent) 
3/32" Head Allen Hex Screwdriver
(Or Equivalent) 

1/4" Nut Driver

Utility Knife

Ui tabs
Ui tab
titleV2 Cabinet

V2 Cabinet Installation

install-stepsINLINE

Required Hardware

c-0103-b,C-2Programfalsefalse

Step 1 - Disconnect Local Reader

  1. Open the front door of the X-Changer cabinet and locate the rear of the local card reader.
  2. Disconnect the relay cable from the rear of the card reader.  (Pull from the plastic connector - pulling on the wires may detach them from the connector.)
  3. Disconnect the Cat5 cable from the rear of the card reader.

Step 2 - Remove the Local Reader

  1. With a utility knife or similar tool, carefully remove the 'Insert Card' decal surrounding the card slot.
  2. Remove the screws on the left and right edges of the card reader.
  3. This may require either the #2 phillips head or 11/32" hex driver - models may vary.
  4. Slide card reader forward and out of the mounting slot.

Step 3 - Install Replacement Reader

c-0103-b,c-2programHeightfalsefalsetrue

  1. Reverse the previous steps to install the new card reader.
    1. Insert reader into mounting slot.
    2. Mount with new or original screws.
    3. Reconnect 6 pin plastic connector to rear of card reader.
    4. Reconnect Cat5 cable to rear of card reader (ports are interchangeable).
  2. .
  3. Test card reader with existing customer or manager card to verify operation.
    1. If operation fails, contact Technical Support.
Ui tab
titleV1 Cabinet

V1 Cabinet Installation

install-stepsINLINE

Required Hardware

c-0100-vc-rrfalsefalse

Step 1 - Disconnect Card Reader

  1. Locate the rear of the local card reader (mounted on the inside of the X-Changer front door).
  2. Disconnect the pulse cable (left) and Cat5 cable (right), highlighted in red.

Step 2 - Remove the Circuit Board from Reader Body

  1. Gently disconnect the magnetic stripe reader from the circuit board (highlighted in red).
  2. Remove the four (4) screws holding the board to the reader body (highlighted in yellow).
  3. Gently lift the circuit board away and set it aside, preferably in a mylar bag or non-conductive, anti-static surface.

Step 3 - Remove Card Reader Body

  1. Using a 1/4" nut driver, remove the kep nuts at the front of the card reader body (there may be a matching pair underneath the reader body).
    1. Set these nuts aside for the replacement reader.
  2. Once all nuts are removed, it is possible to slide the reader body out and away from the X-Changer door.

Step 4 - Install Replacement Reader

  1. On the replacement card reader, remove the circuit board from the card reader body, as shown in Step 2.
  2. Reverse Step 3, installing card reader body onto X-Changer door using the kep nuts and 1/4" nut driver.
  3. Reverse Step 2, installing the circuit board onto the card reader body once all kep nuts are secured.
  4. Set dipswitch #7 to ON position, all other dipswitches set to the OFF position (highlighted in red).
  5. Reconnect pulse cable and Cat5 cable, reversing Step 1.
  6. Test card reader with existing customer or manager card to verify operation.
    1. If operation fails, contact Technical Support.

Additional Information