Versions Compared

Old Version 17

changes.mady.by.user Former user

Saved on

compared with

New Version 18

changes.mady.by.user Former user

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel
borderColor#416EB6
titleColor#E6E6E6
titleBGColor#416EB6
titleOverview

This page is intended to guide the user through the replacement of the button membrane on the F1 FasCard reader.

Panel
borderColor#416EB6
titleColor#E6E6E6
titleBGColor#416EB6
titleOn this Page

Table of Contents
maxLevel2
minLevel2


Multiexcerpt include
MultiExcerptNameWarning
DisableCachingtrue
PageWithExcerptCCIDOC:_General

Required Hardware

Two versions of the touch pad replacement kit exist.  The installation of the button membrane is the same for both versions - the primary difference is in the design of the cover label.  

Type 1

This kit has been replaced by Type 2, below.  It is no longer available.

This kit includes a label to cover the screws on the FasCard reader.  The button membrane is pre-labeled.

Bw part list
PartsC-5021,C-5050
SizingModeHeight
ShowDesc3false
SingleRowtrue

Type 2

This kit includes a label that covers both the screws on the FasCard reader as well as the button membrane.  The button membrane is not pre-labeled.  The C-5052 label must be aligned correctly on top of the button membrane.

Bw part list
PartsC-5051,C-5052
SizingModeHeight
ShowDesc3false
SingleRowtrue

Recommended Tools

Phillips screwdriverRubbing Alcohol

Instructions

Div
Classinstall-steps
Panel
borderColor#416EB6
bgColor#416EB6
titleColor#E6E6E6
titleBGColor#416EB6

Step 1 - Remove Reader Control Board

  1. Remove two screws mounted on each corner of the main card reader board, highlighted in Fig.1a.
  2. Tilt control board away from grey bezel, and lift it out.

Fig. 1aFig. 1bFig. 1c

Panel
borderColor#416EB6
bgColor#416EB6
titleColor#E6E6E6
titleBGColor#416EB6

Step 2 - Disconnect and Remove Existing Button Membrane

  1. Remove blue/silver stripe ribbon cable from wi-fi radio board, highlighted in Fig. 2a. Gently pull up on cable to remove.
  2. Remove the touch pad- the connected ribbon cable should slide out with the button membrane.
  3. Clean the touch pad and cover label surface with rubbing alcohol to remove all adhesive residue.

Fig. 2aFig. 2bFig. 2cFig. 2d

Panel
borderColor#416EB6
bgColor#416EB6
titleColor#E6E6E6
titleBGColor#416EB6

Step 3 - Install New Button Membrane

  1. Fold the touch pad ribbon cable up as shown below. 
  2. Peel off both protective backing pieces to expose the touch pad adhesive.
  3. Insert the folded end of the ribbon cable through the bezel opening. Make sure the fold is facing down so the "up arrow" is on the left and "enter dash" is on right.
    1. If the button membrane replacement is C-5051 type, installation is the same but the C-5052 label must be applied in the correct alignment.  See Fig. 3d and 3e, below.

Fig. 3aFig. 3bFig. 3cFig. 3dFig. 3e

Panel
borderColor#416EB6
bgColor#416EB6
titleColor#E6E6E6
titleBGColor#416EB6

Step 4 - Reconnect Touch Membrane to Control Board

  1. Connect ribbon cable back to wi-fi radio board, then put remaining components back together. (Refer to Step 2 if needed)
    1. If using the older C-5050 Button Membrane, apply the C-5021 screw cover label once the card reader is mounted on the associated machine.

Fig. 4a