Versions Compared

Old Version 1

changes.mady.by.user Former user

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Remove install-steps and div user macros
Note

Card Concepts Inc takes no responsibility for data loss due to human error, hardware failure, or other such circumstances.

Panel
titleTable of Contents
borderStylesolid
Table of Contents

 

 

Panel
titlePurpose
borderStylesolid
Excerpt

This guide will show you on how to replace the touch pad on the fascard reader

Requirements

Fascard Reader (C-5001)Phillips Head & Flathead ScrewdriverTouch Pad (C-5050)Fascard Screw Cover Label (C-5021)Rubbing Alcohol 
Image RemovedImage RemovedImage RemovedImage RemovedImage Removed 

 

 

Removing Touch Pad

  • Unmount Fascard Reader from machine 
  • Place Fascard Reader on a clean working surface.
    • Remove two screws mounted

    Overview

    This page is intended to guide the user through the replacement of the button membrane on the F1 FasCard reader.

    Multiexcerpt include
    MultiExcerptNameWarning
    DisableCachingtrue
    PageWithExcerptCCIDOC:_General

    Required Hardware

    Two versions of the touch pad replacement kit exist.  The installation of the button membrane is the same for both versions - the primary difference is in the design of the cover label.  

    Type 1

    This kit has been replaced by Type 2, below.  It is no longer available.

    This kit includes a label to cover the screws on the FasCard reader.  The button membrane is pre-labeled.

    Bw part list
    PartsC-5021,C-5050
    SizingModeHeight
    ShowDesc3false
    SingleRowtrue

    Type 2

    This kit includes a label that covers both the screws on the FasCard reader as well as the button membrane.  The button membrane is not pre-labeled.  The C-5052 label must be aligned correctly on top of the button membrane.

    Bw part list
    PartsC-5051,C-5052
    SizingModeHeight
    ShowDesc3false
    SingleRowtrue

    Recommended Tools

    Phillips screwdriverRubbing Alcohol
    Image Added

    Image Added

    Instructions

    Step 1 - Remove Reader Control Board

    1. Remove two screws mounted on each corner of the main card reader board
       Image Removed
      Remove ribbon cable connector from main board. Don't put to much force when removing this cable. Remove connector from right to left. 
      Image Removed   Image Removed

       

      Remove touch pad cable from main card reader board. , highlighted in Fig.1a.
    2. Tilt control board away from grey bezel, and lift it out.

    Fig. 1aImage Added Fig. 1bImage Added Fig. 1cImage Added

    Step 2 - Disconnect and Remove Existing Button Membrane

    1. Remove blue/silver stripe ribbon cable from wi-fi radio board, highlighted in Fig. 2a. Gently pull up on cable to remove. 
      Image Removed           Image Removed
        
        Peel off sticker (C-5021) that is around the touch pad.
      Image Removed  Image Removed
      Now remove the touch pad carefully. 
           Image Removed
      The touch pad now should be removed and the front of the reader should now look like this. 
      Image Removed

      Clean the front of the reader with some rubbing alcohol and make sure there is no sticker residue on the reader. 

      Image Removed
      Replacing Fascard Reader with New Touch Pad
       On the end of part # C-5050 there is flap you can fold. Make sure the flap end is pointing up as you see here in this example. 
      Image Removed
    2. Peel off the back end of the touch pad. There are two sections you need to peel off. 
       
    3. Mount the touch pad onto the front of the card reader. Insert the touch pad connection flap through the slit opening of the reader. Make sure the connection flap fold is facing down when inserting. When doing this the touch pad up arrow will be on the left and enter button on right. 
      Image Removed             Image Removed
       Align touch pad sticker onto reader and make sure it fits properly and secure. 
      Image Removed
      Connect touch pad cable back to radio board.
       Image Removed
      Re-Attach ribbon cable connector to main card reader board.
      Image Removed
           
       
    4. Remove the touch pad - the connected ribbon cable should slide out with the button membrane.
    5. Clean the touch pad and cover label surface with rubbing alcohol to remove all adhesive residue.

    Fig. 2aImage Added Fig. 2bImage Added Fig. 2cImage Added Fig. 2dImage Added

    Step 3 - Install New Button Membrane

    1. Fold the touch pad ribbon cable up as shown below.
    2. Peel off both protective backing pieces to expose the touch pad adhesive.
    3. Insert the folded end of the ribbon cable through the bezel opening. Make sure the fold is facing down so the "up arrow" is on the left and "enter dash" is on right.
      1. If the button membrane replacement is C-5051 type, installation is the same but the C-5052 label must be applied in the correct alignment.  See Fig. 3d and 3e, below.

    Fig. 3aImage Added Fig. 3bImage Added Fig. 3cImage Added Fig. 3dImage Added Fig. 3eImage Added

    Step 4 - Reconnect Touch Membrane to Control Board

    1. Connect ribbon cable back to wi-fi radio board, then put remaining components back together. (Refer to Step 2 if needed)
      1. If using the older C-5050 Button Membrane, apply the C-5021 screw cover label once the card reader is mounted on the associated machine.

    Fig. 4aImage Added