Versions Compared

Old Version 1

changes.mady.by.user Brett Norrell (Deactivated)

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID616
KitDescCoin and Card

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID791
KitDescCard Only - 10° Front Panel Coin Models

  1. Remove existing coin box and coin drop/slide.

  2. Remove vault service switch connections from the switch and bridge using the C-5365 Bypass Harness.

  3. Install C-5765-W Vault Bracket over the metercase opening. Secure in place using C-1059 Kep Nuts and C-1070-W Washers.

    1. If installing on a coin slide equipped model the two holes next to the coin slide bolt will need to be enlarged about a 1/4" to allow the mounting studs to pass through the metercase.

  4. Apply C-5027 Label on or near the reader if required for location.

Cci readerinstall kit
KitID905
KitDescCard Only - Card Ready Models

  1. Place the C-5700-TEMP Drill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to for further instructions.

Cci readerinstall kit
KitID910
KitDescCard Only - Flat Front Panel Coin Models
  1. Remove coin drops and coin boxes.
  2. Remove vault service switch connections from the switch and bridge using the C-5365 Bypass Harness.
  3. Take the C-0940 Vault Cover and bend the inner tabs outward.
  4. Insert the C-0940 Vault Cover into the coin box opening. The previously bent tabs should catch the inner lip of the coin vault and secure the bracket in place.

  5. Place the C-5700-TEMP Drill Template on the desired mounting location.

  6. Verify included harnesses will reach desired location without encountering interference from internal machine components.

    1. Suggested mounting location: Coin drop opening.

  7. Refer to for further instructions.

Connect Power

Cci readerinstall kit
KitID581
KitDescACA Controls
  1. Connect the C-6204-40 12VDC Power Harness to the H10 Connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  2. The remaining end (3-pin molex) connects directly to the rear of the F1 FasCard Reader.
Cci readerinstall kit
KitID595
KitDescHybrid Coin Slides & Titanium Controls
  1. Tap power as described in the document using theC-5101 Spade Taps provided.
  2. Connect theC-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to theC-5602 Power Converter.
  3. Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID674
KitDescCoin Drop: Optical Coin Drops
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5250 Coin Sense Harness to the harness connected to the Coin Drop.
Cci readerinstall kit
KitID677
KitDescCoin Drop: Coin Slide
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect the C-5253 Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID636
KitDescPulse - Coin Slide
  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the coin slide micro switch.
Cci readerinstall kit
KitID582
KitDescSerial
  1. Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF1 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in theF1: FasCard Reader Mounting Guide.
  2. Connect the free end of the Machine Start Harness:
    1. If following steps for a serial Machine Start Harnessto port 5 (Serial Connection Port) as shown in the image above.
    2. If following steps for a pulse Machine Start Harnessto port 2 (Pulse Connection Port) as shown in the image above.
  3. Connect the free end of theCoin Sense Harnessto port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of thePower Harness to port 1 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

Machine Configuration

ACA machines using a serial configuration require dip switch 3 on theMachine Control Boardto be set to the 'ON' position.Leave all other dip switches as is.

Cci readerinstall footer