Page Comparison

Step-by-step guide

Step 1 - Powering down the Touch Kiosk

1. Open the front of the Touch Kiosk and plug-in the keyboard in any available USB port on the main CPU board. 
2. Press Press CTRL+ALT+DELETE to bring up the task the Windows Task menu. 
3. Touch the power icon in the lower right-hand corner of the screen. 
4. Select SHUTDOWN the SHUTDOWN option from the optionsnew menu. 
5. Turn off the power supply to the kiosk and unplug the power cord.

Installing the Kit

Parts Required

(1) 8-32 1/2" Screw
C-1079 

(1) M 1/4" Metal Clamp
C-1081 

Image Removed

Image Removed

Image Removed

Tools Required

P1 3" Philips head screwdriver

P2 4" Philips head screwdriver

11/32" Wrench or nut driver

Rear of Kiosk drawer

Step One

1. Locate the shorter C-1063 Screw and the smaller C-1081-M Metal Clamp.Flip the rocker switch so that the "O" is depressed.

Step 2 - Connecting the rear of the Kiosk 

1. Locate the shorter screw (P/N: C-1063) and smaller Metal Clamp (P/N: C-1081-M). 
2. Insert the C-1063 screw into the larger ring on the 4-point harness. 
   Image Removed
   Image Added
   
   
3. Bend the the C-1081-M Metal Clamp clamp around the existing power cable, about 10" from the kiosk the Kiosk end. 
   1. This provides strain relief for the cable. 
4. Insert the the C-1063 1063 screw and 4-point harness through the clamp and secure it to the base of the drawer as indicated shown here:
   Image RemovedImage Removed 
   
   Image Added
   
   

5. The end result should look like the following: 
   
   Image Added
   
   

   Note
   There may be an existing plastic wire clamp and screw, you can discard these.

   
   

Step

3 – Securing the grounding screws

1. Using a P2 Philips screwdriver, remove the two (2) screws securing the power supply protective protector cover and pull . Pull away towards you when removing. 
   Image RemovedImage Removed
   Image Added
   
   
2. NoteBe careful Be cautious when opening the protective cover so as to avoid pulling wires or breaking wire connections between the cover and power supply. Power Supply Unit (PSU). 
   
   Image Added
   
   
3. Loosen the screws on the power supply marked Image Removed (Green Wire) and -V (Black Wire).
   Image Removed the PSU marked with the Image Added symbol (for green wire) and -V (for black wire). 
   
   Image Added
   
   
4. Insert the forked ends of the 4-point harness into the loosened terminals. There should be 2 total plugs on each terminal. 
5. Tighten the terminals and replace the power supply cover, taking care not to pinch any wires. 
   1. There is a notch out of the corner to allow the wires to come out of the cover. 
6. Replace the two (2) screws and tighten down the power supply cover. 
7. Using a P1 Philips screw driverscrewdriver, Remove remove the screw from the base of the card dispenser closest to the power supply.
   Image Removed
   Image Added
   
   
8. Insert the screw through the remaining small ring on the 4-point harness and re. 
9. Re-secure the screw back to the dispenser base. 
   Image Removed
   Image Added

Front of Kiosk Drawer

Step One

Step 4 – Grounding the main CPU board

1. Locate the Power Control Board (PCB) on the back of the front panel. 
   Image Removed
   Image Added
   
   
2. Remove the screw in the lower left-hand corner that is securing a plastic clamp. Image Removed
3. Remove and discard the plastic clamp and replace it with the the C-1083-M Metal Clamp clamp, binding it to the end of the black looming. 
4. Re-secure the clamp to the board with the screw that was removed earlier.
   Image Removed 

Step

5 – Grounding the Bill Note Acceptor (BNA)

1. Remove the lower 11/32" nut on the left side of the assembly the assembly bracket. 
   Image Removed
   Image Added
   
   
2. Put one end of the 2-point harness on the stud and re-secure secured the nut to the stud. 
3. Remove the upper-left Screw screw from the Bill Acceptor BNA and apply the remaining end of the 2-point harness and , re-secure securing it with the C-1063 Screw screw. Image Removed

Step 6 – Powering on and closing the Touch Kiosk

1. Plug-in the power cord to the power supply

Tips & Warnings

1. . 
2. Power on the Touch Kiosk by flipping the rocker switch so the "I" is depressed. 
3. Push the Kiosk drawer closed and lock it. 

Related documentation