Page Comparison

Step-by-step guide

Step 1 - Powering down the Touch Kiosk

1. Open the front of the Touch Kiosk and plug-in the keyboard in any available USB port on the main CPU board. 

1. Press CTRL+ALT+DELETE to bring up

1. the Windows Task menu. 
2. Touch the power icon in the lower right-hand corner of the screen. 
3. Select

1. the SHUTDOWN option from the

1. new menu. 

1. Flip the rocker switch so that the "O" is depressed.

Step 2 - Connecting the rear of the Kiosk 

1. Locate the shorter screw (P/N: C-1063) and smaller Metal Clamp (P/N: C-1081-M). 
2. Insert the C-1063 screw into the larger ring on the 4-point harness. 
   

1. 
   Image Added
   
   
2. Bend

1. the C-1081-M

1. clamp around the existing power cable, about 10" from

1. the Kiosk end. 
   1. This provides strain relief for the cable. 
2. Insert

1. the C-

1. 1063 screw and 4-point harness through the clamp and secure it to the base of the drawer as

1. shown here:

1.  
   
   Image Added
   
   

2. The end result should look like the following: 
   
   Image Added
   
   

   Note
   There may be an existing plastic wire clamp and screw, you can discard these.

   
   

Step

3 – Securing the grounding screws

1. Using a P2 Philips screwdriver, remove the two (2) screws securing the power supply

1. protector cover

1. . Pull away towards you when removing. 
   

1. Image Added
   
   
2. Be

1. cautious when opening the protective cover so as to avoid pulling

1. or breaking wire connections between the cover and

1. Power Supply Unit (PSU). 
   
   Image Added
   
   
2. Loosen the screws on

1. the PSU marked with the Image Added symbol (for green wire) and -V (for black wire). 
   
   Image Added
   
   
2. Insert the forked ends of the 4-point harness into the loosened terminals.

1.  
2. Tighten the terminals and replace the power supply cover, taking care not to pinch any wires. 
   1. There is a notch out of the corner to allow the wires to come out of the cover. 
3. Replace the two (2) screws and tighten down the power supply cover. 
4. Using a P1 Philips

1. screwdriver,

1. remove the screw from the base of the card dispenser closest to the power supply.
   

1. 
   Image Added
   
   
2. Insert the screw through the remaining small ring on the 4-point harness

1. . 
2. Re-secure the screw back to the dispenser base.

1.  
   
   Image Added

Step 4 – Grounding the main CPU board

1. Locate the Power Control Board (PCB) on the back of the front panel. 
   

1. 
   Image Added
   
   
2. Remove the screw in the lower left-hand corner that is securing a plastic clamp.

1.  
2. Remove and discard the plastic clamp and replace it with

1. the C-1083-M

1. clamp, binding it to the end of the black looming. 
2. Re-secure the clamp to the board with the screw that was removed earlier.

Step

5 – Grounding the Bill Note Acceptor (BNA)

1. Remove the lower 11/32" nut on the left side of

1. the assembly bracket. 
   

1. 
   Image Added
   
   
2. Put one end of the 2-point harness on the stud and re-

1. secured the nut to the stud. 
2. Remove the upper-left

1. screw from the

1. BNA and apply the remaining end of the 2-point

1. , re-

1. securing it with the C-1063

1. screw. 

Step 6 – Powering on and closing the Touch Kiosk

1. Plug-in the power cord to the power supply

1. . 
2. Power on the Touch Kiosk by flipping the rocker switch so the "I" is depressed. 
3. Push the Kiosk drawer closed and lock it. 

Related documentation