Versions Compared

Old Version 13

changes.mady.by.user Former user

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Remove install-steps and div user macros
Panel
borderStylesolid
titleTable of Contents
Table of Contents
Panel
borderStylesolid
titlePurpose
ExcerptThis guide will show you on how to replace the touch pad on the FasCard reader

Overview

This page is intended to guide the user through the replacement of the button membrane on the F1 FasCard reader.

Multiexcerpt include
MultiExcerptNameWarning
DisableCachingtrue
PageWithExcerptCCIDOC:_General

Required Hardware

Two versions of the touch pad replacement kit exist.  The installation of the button membrane is the same for both versions - the primary difference is in the design of the cover label.  

Type 1

This kit has been replaced by Type 2, below.  It is no longer available.

This kit includes a label to cover the screws on the FasCard reader.  The button membrane is pre-labeled.

Bw part list
PartsC-5021,C-5050
SizingModeHeight
ShowDesc3false
SingleRowtrue

Type 2

This kit includes a label that covers both the screws on the FasCard reader as well as the button membrane.  The button membrane is not pre-labeled.  The C-5052 label must be aligned correctly on top of the button membrane.

Bw part list
PartsC-5051,C-5052
SizingModeHeight
ShowDesc3false
SingleRowtrue

Recommended Tools

Phillips screwdriverRubbing Alcohol

Removing Old Touch Pad

  • Remove FasCard Reader from machine.
    • Place FasCard Reader on a clean working surface.

    Instructions

    Step 1 - Remove Reader Control Board

    1. Remove two screws mounted screws mounted on each corner of the main card reader board.
      Image RemovedTilt main board away , highlighted in Fig.1a.
    2. Tilt control board away from grey bezel, and lift it out.
      Image RemovedImage Removed

    Fig. 1aImage Added Fig. 1bImage Added Fig. 1cImage Added

    Step 2 - Disconnect and Remove Existing Button Membrane

    1. Remove blue/silver stripe ribbon cable from stripe ribbon cable from wi-fi radio board, highlighted in Fig. 2a. Gently pull up on cable to remove.
      Image Removed
    2. Remove the screw cover label, then remove the touch pad.
      Image RemovedImage Removedthe touch pad - the connected ribbon cable should slide out with the button membrane.
    3. Clean the touch pad and cover label surface with rubbing alcohol to remove all adhesive residue.Image RemovedImage Removed
    Installing New Touch Pad

    Fig. 2aImage Added Fig. 2bImage Added Fig. 2cImage Added Fig. 2dImage Added

    Step 3 - Install New Button Membrane

    1. Fold the touch pad ribbon cable up  up as shown below. 
      Image Removed
    2. Peel off both protective backing pieces to expose the touch pad adhesive.
      Image Removed
    3. Insert the folded end of the ribbon cable through the bezel opening. Make sure the fold is facing down so the "up arrow" is on the left and "enter dash" is on right.
      Image RemovedImage RemovedImage Removed
      1. If the button membrane replacement is C-5051 type, installation is the same but the C-5052 label must be applied in the correct alignment.  See images below for reference.

        Image Removed

        Image Removed

      Connect ribbon cable back
      1. Fig. 3d and 3e, below.

    Fig. 3aImage Added Fig. 3bImage Added Fig. 3cImage Added Fig. 3dImage Added Fig. 3eImage Added

    Step 4 - Reconnect Touch Membrane to Control Board

    1. Connect ribbon cable back to wi-fi radio board, then put remaining components back together.
      Attach cover label after reader is re-mounted to machine.
      Image Removed(Refer to Step 2 if needed)
      1. If using the older C-5050 Button Membrane, apply the C-5021 screw cover label once the card reader is mounted on the associated machine.

    Fig. 4aImage Added