Versions Compared

Version Old Version 17 New Version Current
Changes made by

Chris Kite

Christopher Patac

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Panel
borderColor#416EB6
titleColor#ffffff
titleBGColor#416EB6
titleOverview

This install guide goes over the detailed installation steps for an F2/F3touchscreen FasCard/FLEX reader onto an existing machine in either ahigha high-front or top-mount position.

Note
title

C-5402/C-5426-BASE incompatibility

The below solutions are not compatible with previousused previously used high-front/top mount readers or mounting bases.

title
Warning

Swipe Clearance Notice

For top-mount placements, CCI strongly recommends mounting the frontof front of the top-mount bracket 1-1/4 inches from the front of the machine, toallow to allow for card swipe clearance.

Ensure the drilled hole aligns accordingly. Mounting the top-mount bracketany bracket any further back then 1-1/4inches from the front of the machine to the edge of thereader the reader can potentially interfere with mounting the reader to the bracket andmay and may prevent users from being able to swipe or insert a card into the readerdue reader due to lack of clearance.

Required parts & tools 

FasCard/FLEX reader

tools

Readers

Bw part list
PartsC-5401,C-5403,C-5520
ShowDesc2true
ShowImagetrue
ShowDesc1true
X080-001 (Top

Kits

Expand
titleHigh-Front Mount Kit
) 
Cci kits
KitIDI-
X0020
X0021
ShowKitIDtrue
ShowKitDesctrue
X080-002 (High-Front
Expand
titleTop Mount Kit
)
Cci kits
KitIDI-
X0021
X0020
ShowKitIDtrue
ShowKitDesctrue

Recommended tools & supplies (not included)

Expand
titleItems not included

Multiexcerptexcerpt-include
MultiExcerptNameF2 Tools
PageWithExcerptLCE:Master Excerpt List
LCE:Master Excerpt List
nameFasCard reader tools and supplies
nopaneltrue


Step-by-step guide

Insert excerpt
LCE:Master Excerpt List
LCE:Master Excerpt List
nameWarning
nopaneltrue

Multiexcerpt include
macro_uuid11bdf2e8-444e-40ae-8d37-c63eda678589
SpaceWithExcerptcom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
MultiExcerptNameWarning
PageWithExcerpt_General

Step 1 - Drilling Preparation

  1. Select the part of the machine where the high-front or top-mount bracket will be installed. Ensure this location, whether on the chassis or a panel, is away from any existing components or exposed wiring.

    1. Mark where you may want to mount the reader with a permanent marker if needed.

Image Removed

  1. Whether keeping the chassis/panel intact, exposing, or removing

saidchassis

  1. said chassis/panel, apply some cutting oil where drilling through metal will

takeplace

  1. take place.

  2. Drill the oiled section in question carefully using the tungsten

carbidetipped

  1. carbide tipped hole cutter.
    Image Modified
    Image Modified
    Image Modified

  2. With the drilled hole prepped, you are

nowready

  1. now ready to mount the reader.

Image Removed
  1. Image Added

Step 2 - Mounting the bracket & reader

Tip

Please choose the tab that is associated with the type

ofinstallation

of installation you are completing. 

High-front mount

In a high-front mounting solution where the FasCard

readerwill

reader will be angled downward toward the customer in regard to

tallermachines

taller machines, our C-6465 bracket would be used for

thisinstall

this install.

Image AddedImage Removed
Expand
titleHigh-front mount Step-by-step guide

  1. Attach the C-6465 High Mount Bracket in

itsplace

  1. its place, securing it down with a chase nipple.

Image Removed
  1. Image Added

  2. Mount the universal bracket to the high-

frontbracket

  1. front bracket with two (2) 8-32 screws and feed

theharness

  1. the harness wiring through the center. Whether choosing to

feedwiring

  1. feed wiring first or mounting the bracket first is no problem as

longas

  1. long as the end result (pictured below) is achieved.

Image RemovedImage Removed
  1. Image AddedImage Added

  2. Connect the harnesses to their appropriate locations in the

backof

  1. back of the reader.

    1. For information about where the individual

harnessesconnect

    1. harnesses connect to, please see F2: FasCard Touchscreen Reader. 

Image Removed
    1. Image Added

  2. Slowly mount the reader to the corresponding bracket with

thetop

  1. the top lip catching the locking edge and carefully wedging

thereader

  1. the reader in place. Ensure no metal edges of the bracket

arevisible

  1. are visible.

Image Removed
  1. Image Added

  2. Secure the reader with the provided T15 secure

torxscrews

  1. torx screws on the bottom.

    1. This may be part of the install kits or the

screwsused

    1. screws used from a previous high-front solution.

Image Removed
    1. Image Added
      Note
      titleScrewdriver Angling

      As the reader is angled downward inhigh-front solutions, securing the reader may require a thinner secure torx screwdriver or a flex extension for the appropriate torx bit to accommodate for the angle.

  2. Only F3 FasCard readers – Remove any plastic protectors (if still present) from

thetouchscreen

  1. the touchscreen or EMV chip insert label.

Top-

mount

Mount

Warning
title

Swipe Clearance Notice

As stated above, only for top-mount solutions

thefront

the front of the top-mount bracket 1-1/4 inches from

thefront

the front of the machine, to allow for card swipe clearance.

Ensure the drilled hole aligns accordingly. Mounting

thetop

the top-mount bracket any further back then 1-1/4inches from the front of the machine

tothe

to the edge of the reader can potentially interfere

withmounting

with mounting the reader to the bracket and may prevent

usersfrom

users from being able to swipe or insert a card into the

readerdue

reader due to lack of clearance.

In a top-mount solution, the process differs slightly from

afront

a front or high-front mounting solution. Our C-6452 bracket would be used in this orientation.

Image Added
Expand
Image Removed
titleTop-mount Step-by-step guide

  1. Attach the top-mount bracket onto the top panel of

themachine

  1. the machine, securing down with the chase nipple. Ensure the appropriate wiring is fed through the center

holefor

  1. hole for connecting to the reader.

Image Removed
  1. Image Added

  2. Connect all harnesses to the rear of the touchscreen

readerwhere

  1. reader where required.

    1. For information about where the individual

harnessesconnect

    1. harnesses connect to, please see F2: FasCard Touchscreen Reader.

  
    1. Image Added
Image Removed

  1. Slowly mount the reader to the corresponding bracket with

thetop

  1. the top lip catching the locking edges (shown in red) and

carefullywedge

  1. carefully wedge the reader in place.

    1. Aligning the reader to the top mount also secures the

groundpost

    1. ground post (show in teal) to the reader.

Image RemovedImage Removed
    1. Image AddedImage Added

  2. Secure reader with the included T15 Secure Torx screws on the bottom.

Image Removed
  1. Image Added

  2. Only F3 FasCard readers – Remove any plastic protectors (if still present) from the touchscreen or EMV chip insert label.

Related documentation

Filter by label (Content by label)
showLabelsfalse
showSpacefalse
sortmodified
reversetrue
excludeCurrenttrue
cqllabel in ( "f3reader" ,"f2reader" ) and space = "LCE" and type ="page"