Versions Compared

Old Version 18

changes.mady.by.user David Bussman

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Table of Contents
stylenone

Alliance

Excerpt
nameTitanium Configuration (TLW)

Titanium Controls

Enter 

  1. Enter Manual Mode

 by

  1.  by opening

the 

  1. the service door

 and

  1.  and closing

the 

  1. the coin vault switch. Then press the following two buttons based on the control:

    Quantum Gold Pro (T4)

    MDC II (T1)

    Regular & Normal

    Normal Hot & Perm Press Warm

  2. rAPid

 will

  1.  will be displayed on the control. Select

the 

  1. the Prog

 option

  1.  option and then configure the following settings:

    1. Serial Payment Configuration (SErPAY): Card

    2. Card Enable (CArdEn): On

Exit 

  1. Exit Manual Mode.

Multiexcerptexcerpt
MultiExcerptNamenameMDC Configuration (TLW / FLW)

MDC Controls

  1. Power off the machine.

  2. Connect

the 

  1. the C-0110-CP Jumper Plug

 to

  1.  to the H2

 connection

  1.  connection on the Machine Control Assembly.

  2. Power on the machine.

Multiexcerptexcerpt
MultiExcerptNamenameMDC Configuration (Dryer)

MDC Controls

  1. Power off the machine.

  2. Connect

the 

  1. the C-0110-CP Jumper Plug

 to

  1.  to the H6

 connection

  1.  connection on the Machine Control Assembly.

  2. Power on the machine.

Multiexcerptexcerpt
MultiExcerptNamenameACA Configuration

ACA Controls

  1. Locate the dip switch on the back of the machine's control board.

Set 

  1. Set dip switch 3

 to the 

  1.  to the ON position. 

  2. Leave all other dip switches as is.

Multiexcerptexcerpt
MultiExcerptNamenameCenturion Quantum Gold (C4) - TLW

Centurion Quantum Gold TLW Controls

  1. Power off the machine.

  2. Connect

the 

  1. the C-0110-CP Jumper Plug

 to

  1.  to the H6

 connection

  1.  connection on the Machine Control Assembly.

  2. Power on the machine.

Multiexcerptexcerpt
MultiExcerptNamenameTitanium Configuration (Small Dryer)

Titanium Controls

Enter 

  1. Enter Manual Mode

 by

  1.  by opening

the 

  1. the service door

 and

  1.  and closing

the 

  1. the coin vault switch. Then press the following two buttons based on the control:

    Quantum Gold Pro (T4)

    Galaxy 600 Pro (T2)

    MDC II (T1)

    High Temp & Med TempHigh Temp & Med Temp

    High Temp & Med Temp

  2. rAPid

 will

  1.  will be displayed on the control. Select

the 

  1. the Prog

 option

  1.  option and then configure the following settings:

    1. Serial Payment Configuration (SErPAY): Card

    2. Card Enable (CArdEn): On

Exit 

  1. Exit Manual Mode.

Multiexcerptexcerpt
MultiExcerptNamenameTitanium Configuration (FLW)

Titanium Controls

Enter 

  1. Enter Manual Mode

 by

  1.  by opening

the 

  1. the service door

 and

  1.  and closing

the 

  1. the coin vault switch. Then press the following two buttons based on the control:

    Quantum Gold Pro (T4)

    Galaxy 600 Pro (T2)

    MDC II (T1)

    Regular & NormalHot & Blankets Cold

    Normal Hot & Perm Press Warm

  2. rAPid

 will

  1.  will be displayed on the control. Select

the 

  1. the Prog

 option

  1.  option and then configure the following settings:

    1. Serial Payment Configuration (SErPAY): Card

    2. Card Enable (CArdEn): On

Exit 

  1. Exit Manual Mode.

MultiExcerptName
Multiexcerptexcerpt
MultiExcerptNamenameTitanium Configuration (FLW/Small Dryer)

Titanium Controls

Enter 

  1. Enter Manual Mode

 by

  1.  by opening

the 

  1. the service door

 and

  1.  and closing

the 

  1. the coin vault switch. Then press the following two buttons based on the control:


    Quantum Gold Pro (T4)

    Galaxy 600 Pro (T2)

    MDC II (T1)

    DryerHigh Temp & Med TempHigh Temp & Med Temp

    High Temp & Med Temp

    WasherRegular & NormalHot & Blankets ColdNormal Hot & Perm Press Warm

  2. rAPid

 will

  1.  will be displayed on the control. Select

the 

  1. the Prog

 option

  1.  option and then configure the following settings:

    1. Serial Payment Configuration (SErPAY): Card

    2. Card Enable (CArdEn): On

  • Exit Manual Mode.
    • Multiexcerpt

    1. Exit Manual Mode.

    Excerpt
    nameMidas

    Alliance Touch Controls

    1. Enter the service menu by touch and holding on the top-center of the touch screen for 3 seconds.

      1. Enter password if required.

    2. Configure the machine with the following settings:

      1. Payment Settings:

        • Card Reader: Enabled

        • Serial Payment System: Enabled

    Maytag

    MultiExcerptName
    Excerpt
    nameMayTag Gen1 MLV+ Pulse

    MayTag AA3/Debit Connection Payment Pulse

    1. Enter Service Mode by activating the service switch.

    2. Locate Coin/Debit Option (J.) and set to Cd

    .
    Multiexcerpt

    1. .

    Excerpt
    nameMayTag Gen2 Serial

    Enhanced Debit (Gen 2)

    Enhanced Debit is self-selected when a Generation 2 card reader is installed in the dryer. The Ed option cannot be manually selected or deselected.

    LaundryLux / Electrolux

    multiexcerpt
    Excerpt
    nameEncore - FLW
    Press the Service Switch to enter 

    Encore FLW Controls

    1. Press the Service Switch to enter Service Mode. The display will go blank.

    2. Press

    the 

    1. the Heavy Soil

     and 

    1.  and Extra Rinse buttons

     simultaneously

    1.  simultaneously. The display will show

    either 

    1. either "0 00"

     if

    1.  if in coin mode

    and 

    1. and "1 00"

     if

    1.  if in card mode.

    2. If in coin mode, press

    the 

    1. the Start button. The display will begin flashing.

    2. Press

    the 

    1. the Cold button

     to

    1.  to change the left-most digit

    from 

    1. from "0"

     to 

    1.  to "1".

    2. Press

    the 

    1. the Start button. The display will stop flashing.

    2. Press

    the 

    1. the Service Switch

     to exit 

    1.  to exit Service Mode.

    LG

    MultiExcerptName
    Excerpt
    MayTag Gen2 Serial

    Enhanced Debit (Gen 2)

    Enhanced Debit is self-selected when a Generation 2 card reader is installed in the dryer. The Ed option cannot be manually selected or deselected. 

    Multiexcerpt
    MultiExcerptNamenameLG Giant-C (Pre 1.8/WiFi 2.0)

    LG Controls

    1. Enter Programming Mode on the machine.

      Card ModelCoin ModelOPL Model
      1. Insert service card.
      2. Display will show L9C1.
      1. Dissemble upper coin box key.
      2. Take out the coin drop from the coin box.
      3. Turn on/off the toggle switch at the back of the coin box.
      4. Display will show L9C1.
      1. Push the 1st & 3rd button at the same time.
      2. Push the 2nd button 3 times.
      3. Push the START button.
      4. Display will show L9C1.

    2. Navigate to StUP>FEA1>VEnd and set to CArd.

    3. Exit Programming Mode.

    Multiexcerptexcerpt
    MultiExcerptNamenameContinental ProfitPlus

    ProfitPlus Controls

    1. Connect the washer and open the door. The display will show door.

    2. Press and hold down key 1 until the Cod report appears on the display.

    3. Enter the access code into the menus by pressing the sequence of eight keys of the code without interruption. In basic configuration (when the machine is delivered) the access code to ADVANCED MODE is: 12341234.

    4. If the sequence entered is correct, the display will show Pro, corresponding to the first menu ADVANCED MODE.

    5. Keys 2 and 4 allow the selection of the precedent table menus. The menu selected is shown on the display following its keyword. To enter in it, press key 1 when displaying it.

    6. Navigate to Mod > ID and set value to '1'.

    7. Exit ADVANCE MODE.

    Continental

    Excerpt
    nameContinental HS7

    HS7 Controls

    1. Swipe horizontally the upper left corner of the screen (Swipe at least 1/3 the way across the top of the screen for best results.).

    2. (If password is enabled) Enter the 4-digit numeric code (default: 1-2-3-4).

    3. Enter into the system settings menu.

    4. Select the Gear Icon, then navigate to Connectivity > Internal GirNet.

    5. Enable the Active option.