Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.Feed the harness ends through thecoin vault opening and then through the circular opening in theC-6936Vault Mount Bracket.Spread theC-6936Vault Mount Bracketwings outward and then insert theC-6936Vault Mount Bracketinto thecoin vault.
  • Feed the harness ends through the C-5414 F2 Mounting Bracket.
    • Secure theC-5414F2 Mounting Bracketto theC-6936 Vault Mount Bracket with theC-0144Screws.Install theC-5710 Rubber Grommetinto the circular opening of the C-5414 F2 Mounting Bracket.
  • Remove any existing coin drop.
  • Mount the C-0905 Drop Cover using existing mounting hardware where the coin drop was previously installed.
    • cci-readerinstall-kit
    KitID841
    KitDescCoin and Card
    Cci readerinstall kit
    KitID842
    KitDescCard Only

    Connect Power

    ...

    KitID617

    ...

    1. 120vac: Connect the brown and blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.

    2. 240vac: Connect the brown and blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.

    3. Secure the green wire beneath the ground screw.

    ...

    Connect Coin Sense Harness

    Cci readerinstall kit
    KitID704
    KitDescCoin Drop: Micro Switch
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.
    Cci readerinstall kit
    KitID723
    KitDescCoin Drop: Aftermarket Imonex
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6382 Coin Sense Harness to the harness connected to the Coin Drop.
    Cci readerinstall kit
    KitID704
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6258 Coin Sense Harness to the harness connected to the Coin Drop.

    Connect Machine Interface Harness

    Cci readerinstall kit
    KitID634
    KitDescPulse - Optical
    1. Connect the C-5254 Machine Start Harness to the P3 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID636
    KitDescPulse - Micro Switch
    1. Connect the C-5256 Machine Start Harness to the harness previously connected to the coin drop micro switch.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
    2. Connect the free end of the Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    3. Connect the free end of the Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    4. Connect the free end of the C-5500-115 Power Harness to port 1.
    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    step
    componentMounting

    Cci readerinstall step
    componentPower

    Cci readerinstall step
    componentCoin Sense

    Cci readerinstall step
    componentStart

    Cci readerinstall step
    componentReader

    Cci readerinstall footer