0578 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User
1 min read

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Tumble Dryer (Stack)
Manufacturer: Dexter
Make: Dexter
Model Length: Not Set

Associated Models


DDAD30KCA
DDAD30KCA65
DDAD30KCA65EC
DDAD30KCB65
DDAD30KCB65CN
DDAD30KCB65CNTS
DDAD30KCB65NC
DDAD30KCB65TS
DDAD30KCB65US
DDAD30KCB65USTS
DDAD30KCK
DDAD30KCS
DDAD30KCS65
DDAD30KCS65CN
DDAD30KCS65EC
DDAD30KCS65ECTS
DDAD30KCS65TS
DDAD30KCS65US
DDAD30KCS65USTS
DDAD30KCW
DDAD30KCW65
DDAD30KCW65CN
DDAD30KCW65CP
DDAD30KCW65EC
DDAD30KCW65US
DDAD30KCX65CN
DDAD30KCX65US
DDAD30KCY65CN
DDAD30KCY65US
DDAD30KCY65USPS
DDAD30KCZ65US
DDAD50KCA65
DDAD50KCA65EC
DDAD50KCB65CN
DDAD50KCB65CNTS
DDAD50KCS
DDAD50KCS65
DDAD50KCS65CP
DDAD50KCS65EC
DDAD50KCS65TS
DDAD50KCS65US
DDAD50KCW65
DDAD50KCW65CN
DDAD50KCW65EC
DDAD50KCW65TS
DDAD50KCX65US
DDAD50KCY65US
DDAD50KCY65USTS
DDAG30KCS65
DDAG30KCW65
DDTD30KCS
DDTD30KCS65
DDTD30KCS65ECXC
DDTD30KCS65XC
DDTD30KCW65ECXC
DDTD30KCW65XC

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0006

Part #: C-5213

Desc 1: Power Adapter Harness

Desc 2: DDAD - AC

   Qty: 1

Part #: C-5500-115

Desc 1: Power Extension Harness

Desc 2: 115"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

  1. Connect the C-5213 Power Adapter Harness to the machine AC power terminals.

    • For 120vac models:

      • Connect the Black wire to the L1 tap.

      • Connect the White wire to the N tap.

    • For 240vac models:

      • Connect the Black wire to the L1 tap.

      • Connect the White wire to the L2 tap.

  2. Connect the Green/Yellow wire to the Ground tap.

  3. Connect the opposite end of the C-5213 Power Adapter Harness to the C-5602R1 Power Converter.

  4. Connect the C-5500-115 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.

Connect Machine Interface Harness

 I-T0040

Part #: C-5256

Desc 1: Machine Start Harns (pulse)

Desc 2: 20" - Male taps, Rq. Female

   Qty: 1

  1. Connect the C-5256 Machine Start Harness to the harness previously connected to the micro switch on the coin drop/slide.

CCI Software Configuration

Machine ControlPulseSerial
A-Series (1.0)SingleVend (Relay) / 55ms*NOT SUPPORTED*

Additional Resources