Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Remove existing coin box and coin mechanism.

  • Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.

    • Attach the C-5414 Reader Bracketto the C-6911 Metercase Bracketusing(2)C-542010-32 x 1/4 Pan Screws.Insert the reader harnesses through the hole in the C-6911 Metercase Bracketand then insert the bracket into the metercase opening.Secure the C-6911 Metercase Bracket to the metercase using the C-0301Mounting Bolt.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID860
    KitDescCard Only - Coin Model
    step
    componentMounting

    Remove the (4) Security T20 retaining screws from the front of the machine.
    Lift up and pull panel forward and lay on machine.NOTE: The front panel may come apart, as it is two parts. Take care not to damage the ribbon cable.
    Mount theC-6980Mounting Bracketon the front of the panel so that the holes match on the right and the retaining screw on the back of the plate goes through the card slot.
    Place theC-1070-W WasherandC-1042Keps Nutonto the retaining screw and tighten using 11/32 socket to secure the mounting bracket. The bracket should feel slightly loose until the panel is reattached to the machine.
    cci-readerinstall-kit
    KitID998
    KitDescCard Only - Card Model

    ...

    step
    componentPower

    Locate the 120v power lines in the machine. These wires are usually black and white and are located just inside the back of the panel. Use a voltage tester to confirm the correct wiring.
    Apply theC-5101Spade Tapsto both the black and white power wires and clamping them down with pliers.
    Plug the brown wire of theC-5336Power Adapter Harnessto the white/neutral wire tap and the blue wire to the black/L1 wire tap.
    Locate a green chassis ground screw and loosen to insert the green wire from theC-5336Power Adapter Harnessand retighten.
    Connect the 3-pin connector from theC-5336 Power Adapter Harnessto theC-5602R1Power Converter.
    Apply theC-1098Velcroto theC-5602R1Power Converterand secure inside the machine's panel.
    Connect the 4-pin connector from theC-5500 Power Extension Harness to the C-5602R1 Power Converter.Route the 3-pin connector from theC-5500Power Extension Harnessthrough the open card slot on the machine control panel.
    cci-readerinstall-kit
    KitID999
    KitDescTap 120v Power

    ...

    step
    componentCoin Sense

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect theC-6362 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kitstep
    KitID721
    KitDescCoin Drop - Factory Optical

    ...

    componentStart

    Locate theAA3 serial connectionon the machine control board and plug in theC-5364Machine Start Harness.
    cci-readerinstall-kit
    KitID590
    KitDescPulse/Serial - Debit (AA3) Connection

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameMayTag Gen1 MLV+ Pulse
    PageWithExcerpt_Machine Configuration

    ...