3105 Reader Install Guide

Part #: C-6801

Desc 1: F2/F3 Reader Mounting Kit

Desc 2: Universal

   Qty: 1

1. Place the C-6700-TEMP Drill Template on the desired mounting location.

2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

3. Refer to FasCard Mounting Guide for further instructions.

Part #: C-0303

Desc 1: Topload Mounting Bolt

Desc 2:

   Qty: 1

Part #: C-6911

Desc 1: F2 Metercase Bracket

Desc 2: Whirlpool - White

   Qty: 1

Part #: C-5420

Desc 1: Screw

Desc 2: 10-32 x ¼" - Pan

   Qty: 2

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

Part #: C-5414

Desc 1: F2/F3 Std. Mounting Bracket

Desc 2: Sheet metal base

   Qty: 1

1. Remove existing coin box and coin mechanism.

2. Run reader harnesses through the metercase and out the opening where the coin mechanism was mounted.

3. Attach the C-5414 Reader Bracket to the C-6911 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.
4. Insert the reader harnesses through the hole in the C-6911 Metercase Bracket and then insert the bracket into the metercase opening.
5. Secure the C-6911 Metercase Bracket to the metercase using the C-0301 Mounting Bolt.

Part #: C-6980

Desc 1: Maytag Bk Splash Mount

Desc 2: F2

   Qty: 1

Part #: C-1042

Desc 1: Nut

Desc 2: 8-32 - Kep

   Qty: 1

Part #: C-1070-W

Desc 1: Washer - Build: XCH

Desc 2: 1/4" x 1" O.D.

   Qty: 1

Part #: C-5416

Desc 1: Screw

Desc 2: 8-32" x 3/8" - Button - Torx

   Qty: 2

1. Remove the (4) Security T20 retaining screws from the front of the machine.
   
2. Lift up and pull panel forward and lay on machine. NOTE: The front panel may come apart, as it is two parts. Take care not to damage the ribbon cable.
   
   
3. Mount the C-6980 Mounting Bracket on the front of the panel so that the holes match on the right and the retaining screw on the back of the plate goes through the card slot.
   
4. Place the C-1070-W Washer and C-1042 Keps Nut onto the retaining screw and tighten using 11/32 socket to secure the mounting bracket. The bracket should feel slightly loose until the panel is reattached to the machine.
   

Part #: C-1098

Desc 1: 3M Dual Lock 1" wide

Desc 2: Use 4" strips for C-5602

   Qty: 1

Part #: C-5101

Desc 1: Spade Taps

Desc 2: 18-14 AWG

   Qty: 2

Part #: C-5336

Desc 1: Power Adapter Harness

Desc 2: Dexter Stack

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

1. Locate the 120v power lines in the machine. These wires are usually black and white and are located just inside the back of the panel. Use a voltage tester to confirm the correct wiring.
   
2. Apply the C-5101 Spade Taps to both the black and white power wires and clamping them down with pliers.
   
3. Plug the brown wire of the C-5336 Power Adapter Harness to the white/neutral wire tap and the blue wire to the black/L1 wire tap.
   
4. Locate a green chassis ground screw and loosen to insert the green wire from the C-5336 Power Adapter Harness and retighten.
   
5. Connect the 3-pin connector from the C-5336 Power Adapter Harness to the C-5602R1 Power Converter.
   
6. Apply the C-1098 Velcro to the C-5602R1 Power Converter and secure inside the machine's panel.
   
7. Connect the 4-pin connector from the C-5500 Power Extension Harness to the C-5602R1 Power Converter.
8. Route the 3-pin connector from the C-5500 Power Extension Harness through the open card slot on the machine control panel.
   

Part #: C-6362

Desc 1: Coin Sense Harness

Desc 2: MLG

   Qty: 1

1. Disconnect the Coin Drop from the Machine Control Assembly.
2. Connect the C-6362 Coin Sense Harness to the harness connected to the Coin Drop.

Part #: C-5364

Desc 1: Machine Start Harness

Desc 2: Maytag MFR

   Qty: 1

Locate the AA3 serial connection on the machine control board and plug in the C-5364 Machine Start Harness.