Versions Compared

Version Old Version 3 New Version Current
Changes made by

CCI Integration User

CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.Install theC-5702Chase Nippleinto theC-5414F2 Mounting Bracketusing theC-5703Nut.Feed the remaining harness ends through the open face of theCoin Vault.Spread theC-6936Vault Mount Bracketwings outward before insertion to lock bracket into place.Feed remaining harness ends through theC-6936Vault Mount Bracket.Insert theC-6936Vault Mount Bracketinto theCoin Vault.Feed the remaining harness ends through the combinedC-5414F2 Mounting Bracket.Secure the combinedC-5414F2 Mounting Bracketto theC-6939 Vault Mount Bracket with theC-0144Screws.

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

  • Place C-5035 Label over card slot opening.
    • Refer to for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID667
    KitDescCard Only - Coin Ready
    Cci readerinstall kit
    KitID966
    KitDescCard Only - Card Ready

    ...

    step
    componentMounting

    Cci readerinstall step
    componentPower

    Tap power as described in the document by connecting theC-5338Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.
    1. 120vac- Connect Brown and Blue wires to connector #2 closest to outside of machine and #4 on terminal side closest to circuit board.
    2. 240vac- Connect Brown and Blue wires to connectors 3 and 5 on the terminal side closest to the circuit board.
    3. Secure the green wire beneath the ground screw.
    Connect the opposite end of theC-5338 Power Adapter Harnessto theC-5602 Power Converter.Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.
    cci-readerinstall-kit
    KitID473

    ...

    step
    componentCoin Sense

    cci-readerinstall-kitstep
    KitID704
    KitDescCoin Drop: Factory
    1. Disconnect the Coin Drop from the Machine Control Assembly.
    2. Connect the C-6253 Coin Sense Harness to the harness connected to the Coin Drop.

    ...

    componentStart

    cci-readerinstall-kit
    KitID634
    KitDescPulse
    1. Connect the C-5254 Machine Start Harness to the P2 connector on the Machine Control Assembly.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
    2. Connect the free end of the C-5254 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    3. Connect the free end of the C-6253 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    4. Connect the free end of the C-5500 Power Harness to port 1.
    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    step
    componentReader

    Cci readerinstall footer