3279 Reader Install Guide

Owned by Chris Kite
Last updated: Jan 26, 2024 by CCI Integration User

Warning!

This document assumes the installer has working knowledge of hand tools and of the target machine in question. Physical modification of machine may be required, including modification of machine panels and internal modification to accommodate cables or harnesses.

It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or for any damage that may occur to target machine.

Overview

Equipment Details

Type: Washer Extractor
Manufacturer: Dexter
Make: Dexter
Model Length: Not Set

For card only installations, customer has to clarify if machine is a coin or card prepped model to select the correct mounting kit.

If coin and card installation, customer must clarify what type of coin drop is installed in the machine. Mechanical or Optical.

Associated Models

WCVD18KCS10
WCVD18KCS10USA0
WCVD18KCS12
WCVD18KCS12EC1X
WCVD18KCS12SSBS
WCVD18KCS12USA
WCVD18KCS12USX
WCVD20KCS12
WCVD20KCS12USSZ
WCVD25KCS10
WCVD25KCS12
WCVD25KCS12USA
WCVD30KCS12
WCVD30KCS12USSZ
WCVD40KCS10
WCVD40KCS12
WCVD40KCS12000
WCVD40KCS120000
WCVD40KCS12EC1X
WCVD40KCS12USA
WCVD50KCS12
WCVD55KCS000000
WCVD55KCS10
WCVD55KCS12
WCVD55KCS120000
WCVD55KCS12EC1X
WCVD55KCS12SSBS
WCVD55KCS12USA
WCVD55KCS12USSZ
WCVD55KCS12USX
WCVD55KCS12USXX
WCVD75KCS12
WCVD75KCS12EC1X
WCVD75KCS12USA
WCVD75KCS12USA0

Recommended Tools and Supplies

  • Drill

  • 1 1/8" Tungsten Carbide Tipped Hole Cutter

  • Cutting Oil

  • 9/64" Drill Bit

  • Center Punch

  • Hammer

  • Fine Point Permanent Marker

  • Pliers

  • Tape Measure

Installation

Connect Power

 I-P0001

Part #: C-5602R1

Desc 1: Power Converter

Desc 2: SMT-012-018VW

   Qty: 1

Part #: C-5500

Desc 1: Power Extension Harness

Desc 2: 25.5"

   Qty: 1

Part #: C-5338

Desc 1: Power Adapter Harness

Desc 2: WCAD

   Qty: 1

  1. Tap power as described in the FasCard Reader Install - Universal Concepts document by connecting the C-5338 Power Adapter Harness to the power distribution panel inside the machine or tapping as needed.

    1. 120vac: Connect Blue wire to L1, and Brown wire to N on the terminal side.

    2. 240vac: Connect Blue wire to the L1 tab, and the Brown wire to the L2 tab on the terminal block.

    3. Secure the green wire beneath the ground screw.

  2. Connect the opposite end of the C-5338 Power Adapter Harness to the C-5602 Power Converter.

  3. Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.

CCI Software Configuration

Machine ControlPulseSerial
*NO NAME*SingleVend (Relay) / 55ms*NOT SUPPORTED*

Additional Resources