Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kitstep
    KitID584
    KitDescCoin and Card
    componentMounting

    Remove coin dropand install C-0900Drop Cover.
    1. Secure using the (4) C-1013 6-32 Keps Nuts.
  • Spread the C-6936 Vault Mount Bracket wings outward before insertion to lock bracket into place.
  • Insert the C-6936 Vault Mount Bracket into the coin vault.
    • Secure the C-5414 F2 Mounting Bracketto the C-6936 Vault Mount Bracket with the (2) C-0144 8-32 x 2" Screws.
    cci-readerinstall-kit
    KitID866
    KitDescCard Only

    ...

    step
    componentPower

    Tap power as described in the document using theC-5101 Spade Taps provided.Connect theC-5210 Power Adapter Harnessto the installed spade taps.Connect theC-5210 Power Adapter Harness to theC-5602 Power Converter.Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.Connect the opposite end of theC-5210 Power Adapter Harnessto theC-5602 Power Converter.Connect theC-5500 Power Extension Harness to the appropriate connector on theC-5602 Power Converter. The remaining cable end connects to the FasCard reader.
    cci-readerinstall-kit
    KitID595
    KitDescTap Machine Power

    ...

    step
    componentCoin Sense

    Cci readerinstall kit
    KitID886
    KitDescCoin Drop: Coin Micro

    1. Disconnect the existing wires from the Coin Drop and connect the C-6334 Combination Coin/Start Harness to the Coin Drop.

      1. Blue wires go to common (Co) and normally open (NO) on coin switch.

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect the C-6335 Combination Harness (3-pin, black connector) to the Coin Eye Sensor.The White wire (female) spade connectors bundled with the black connector attach to theCoin Blocksolenoid.
    cci-readerinstall-kitstep
    KitID888
    KitDescCoin Drop: Coin Rotary

    Connect Machine Interface Harness

    componentStart

    Cci readerinstall kit
    KitID886
    KitDescPulse - Coin Micro

    1. Disconnect the existing wires from the Coin Drop.

      1. Connect the C-6334 Machine Start Harness to the Coin Drop.

      2. Connect the Violet wires to Blue wires 36 & 35.

      3. White wires wrapped with Violet go to Red wires 207 & 30.

      4. White wires wrapped with Blue go to Brown coin blocking solenoid wires.

        1. Wrap the connectors in electrical tape to keep the bare terminals from exposing.

    Connect the Violet wire (male) spade connectors to theCoin Sense Input.Connect the remaining White wire (male) spade connectors to theCoin Blocksolenoid drive.
    cci-readerinstall-kitstep
    KitID888
    KitDescPulse - Coin Rotary

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    componentReader

    Cci readerinstall footer