Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Remove existing coin box.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.Bend the side tabs of theC-6936Bracketoutward and install into the coin vault. The tabs should snap into place securing the bracket.Attach theC-5414F2 Mounting Bracketto the Coin Vault Bracketusing C-0144 screws.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID851
    KitDescCard Only

    Connect Power

    step
    componentMounting

    Tap power as described in the document using the C-5101 Spade Taps provided.
  • Connect the C-5336 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602 Power Converter.
  • Connect the C-5500 Power Extension Harness to the appropriate connector on the C-5602 Power Converter. The remaining cable end connects to the FasCard reader.
    • cci-readerinstall-kit
    KitID663

    ...

    step
    componentPower

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kit
    KitID700
    KitDescCoin Drop: Factory
    step
    componentCoin Sense

    Disconnect the Coin Eye Harnessfrom theCoin Drop.
  • Connect the C-6307 Coin Sense Harness end with the red, blue, and green wires to the harness connected to the Coin Drop.
  • Connect the matching two white male connectors on the C-6307 Machine Start Harness to the wires previously connected to the Coin Blocking Solenoid.
    • cci-readerinstall-kit
    KitID883
    KitDescCoin Drop: MD2 Control

    Connect Machine Interface Harness

    step
    componentStart

    cci-readerinstall-kitstep
    KitID645
    KitDescPulse
    1. Connect the C-5300-NC Machine Start Harness to the Coin 1 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID883
    KitDescPulse - MD2 Control
    1. Connect the C-6307 Machine Start Harness connector with the purple wires to the Coin Counting Board Harness where the coin drop was previously connected.
    2. Connect the matching two white female connectors on the C-6307 Machine Start Harness to the Coin Blocking Solenoid.

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    1. Feed remaining harness ends through the mounting hole as described in the F2/F3: FasCard Reader Mounting Guide.
    2. Connect the free end of the C-5300-NC, or C-6307 Machine Start Harness to port 2 (Pulse Connection Port) as shown in the image above.
    3. (Coin and Card Installation Only) Connect the free end of the C-6250, or C-6307 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
    4. Connect the free end of the C-5500 Power Extension Harness to port 1 (C-5500 Power Harness Connection Port) as shown in the image above.
    5. Secure the FasCard reader to base as described in the FasCard Mounting Guide.

    Machine Configuration

    ...

    componentReader

    Cci readerinstall footer