Versions Compared

Version Old Version 3 New Version Current
Changes made by

CCI Integration User

CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Remove existing coin box and coin drop.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.Attach theC-5414 F2 Mounting Bracketto the C-6765-W-R1 Metercase Bracketusing (2) C-5420 10-32 x 1/4 Pan Screws.Run any card reader harnesses through the coin slot openings and the circular hole in theC-6765-W-R1Metercase Bracket.Install theC-6765-W-R1Metercase Bracketso that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nutsand (2) C-1070-WWashers.

  • Remove existing coin box and coin drop.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.Bend the tabs outward and insert theC-0940 Vault Cover in to the coin vault opening.
  • Apply the C-5035 Label over the opening for the coin drop.
    • Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kit
    KitID584
    KitDescCoin and Card
    Cci readerinstall kit
    KitID857
    KitDescCard Only - 10° Panel Coin Models
    Cci readerinstall kit
    KitID911
    KitDescCard Only - Flat Front Panel Coin Models
    Cci readerinstall kit
    KitID906
    KitDescCard Only - Card Models

    ...

    step
    componentMounting

    Cci readerinstall step
    componentPower

    Connect theC-6204-40 12VDC Power Harnessto theH10connection on the Machine Control Assembly.
    1. Connect the green wire to a chassis ground.
  • The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
    • Connect the 2-pin connector from theC-6207 F2, ACA Power Harnessto the 24v transformer behind the front control panel.
  • The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
    • Tap power as described in the document using the C-5101 Spade Taps provided.
  • Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602R1 Power Converter.
  • Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.
    • cci-readerinstall-kit
    KitID581
    KitDescACA Controls
    Cci readerinstall kit
    KitID837
    KitDescTitanium Controls
    Cci readerinstall kit
    KitID794
    KitDescACA Controls with Electronic Coin Drops

    ...

    step
    componentCoin Sense

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect theC-6250 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kit
    KitID700
    KitDescFactory Optical Coin Drop

    Connect Machine Interface Harness

    Connect theC-5300-NC Machine Start Harness to the coin 1 connector on the Machine Control Assembly.
    Cci readerinstall kit
    KitID648
    KitDescPulse - Coin
    step
    componentStart

    Connect theC-5240 Machine Start Harness to the the H3connection on the Machine Control Assembly or Communication board.
    cci-readerinstall-kit
    KitID582
    KitDescSerial Communication / Serial Pulse

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameACA Configuration
    PageWithExcerpt_Machine Configuration

    ...