Versions Compared

Old Version 3

changes.mady.by.user CCI Integration User

Saved on

compared with

New Version Current

changes.mady.by.user CCI Integration User

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.
    cci-readerinstall-kitstep
    KitID584
    KitDescCoin and Card
    componentMounting

    Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Remove existing coin box.

    • Install theC-5365 Bypass Harnessby removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.Bend the side tabs of theC-0940Vault Coveroutward and install into the coin vault. The tabs should snap into place securing the bracket.Place theC-6700-TEMPDrill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to for further instructions.

  • Remove existing coin box and coin drop.

    • Attach C-5760-A Alliance Adapter Bracketto C-6760 Metercase Bracket.Attach theC-5414 Mounting Bracketto C-6760Metercase Bracket using the(2)C-5420 10-32 x 1/4 Pan Screws.Mount C-6760 Metercase Bracketinto the front of the metercase, inserting the two studs through the coin slot openings.Secure to the metercase using(2)C-1059Keps Nutsand(2)C-1070-WWashers.
    cci-readerinstall-kit
    KitID906
    KitDescCard Only - Card Model
    Cci readerinstall kit
    KitID911
    KitDescCard Only - Coin Model w/ Front Control Panel
    Cci readerinstall kit
    KitID916
    KitDescCard Only - Coin Model w/ Rear Control Panel

    ...

    step
    componentPower

    Tap power as described in the document by connecting theC-5210Power Adapter Harnessto the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Secure the green wire to the ground wire.

    Connect the opposite end of theC-5210Power Adapter Harnessto theC-5602R1Power Converter.Connect theC-5500Power Extension Harness to the appropriate connector on theC-5602R1Power Converter. The remaining cable end connects to the FasCard reader.
    cci-readerinstall-kit
    KitID595
    KitDescTap 120v Machine Power

    ...

    step
    componentCoin Sense

  • Disconnect the Coin Drop from the Machine Control Assembly.
    • Connect theC-6250 Coin Sense Harness to the harness connected to the Coin Drop.
    cci-readerinstall-kitstep
    KitID700
    KitDescCoin Drop - Optical

    ...

    componentStart

    Connect theC-0110-TOP Machine Start Harnessto the machine control assemblyat:
    1. H5 for MDC controls.
    2. H4 for Centurion controls.
  • (Serial Communication Setup Only) Replace the existing Alliance Jumper Plug with C-0110-CP Jumper Plug at:
    1. H2 for MDC controls.
    2. H6 for Centurion controls
    • cci-readerinstall-kit
    KitID603
    KitDescSerial / Pulse - MDC & Centurion Control

    Connect and Mount Reader

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameF2 Reader
    PageWithExcerpt_Reader Ports

    ...

    step
    componentReader

    Machine Configuration

    Multiexcerpt include
    SpaceWithExcerptCCIDOC
    MultiExcerptNameMDC Configuration (TLW / FLW)
    PageWithExcerpt_Machine Configuration

    ...