Install Mounting Hardware
| cci-readerinstall-kit |
|---|
| KitID | 584 |
|---|
| KitDesc | Coin and Card |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 857 |
|---|
| KitDesc | Card Only - 10° Panel Coin Models |
|---|
|
Remove existing coin box and coin drop.
Install the C-5365 Bypass Harness by removing the coin vault switch and connecting the spade terminal connections to C-5365 Bypass Harness.
Attach the C-5414 F2 Mounting Bracket to the C-6765-W-R1 Metercase Bracket using (2) C-5420 10-32 x 1/4 Pan Screws.
Run any card reader harnesses through the coin slot openings and the circular hole in the C-6765-W-R1Metercase Bracket.Install the C-6765-W-R1 Metercase Bracket so that the two threaded posts insert into the coin drop slots. Then secure it to the machine using the (2) C-1059 Kep Nuts and (2) C-1070-W Washers.
| Cci readerinstall kit |
|---|
| KitID | 906 |
|---|
| KitDesc | Card Only - Card Models |
|---|
|
Place the C-6700-TEMP Drill Template on the desired mounting location.
Verify included harnesses will reach desired location without encountering interference from internal machine components.
Refer to FasCard Mounting Guide for further instructions.
...
| cci-readerinstall-kitstep |
|---|
| KitID | 581 |
|---|
| KitDesc | ACA Controls |
|---|
|
Connect the C-6204-40 12VDC Power Harness to the H10 connection on the Machine Control Assembly. Connect the green wire to a chassis ground.
The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
| Cci readerinstall kit |
|---|
| KitID | 837 |
|---|
| KitDesc | Titanium Controls |
|---|
|
Connect the 2-pin connector from the C-6207 F2, ACA Power Harness to the 24v transformer behind the front control panel. The remaining end (3-pin molex) connects directly to the rear of the F2 FasCard Reader.
|
...
| KitID | 794 |
|---|
| KitDesc | ACA Controls with Electronic Coin Drops |
|---|
...
Connect the C-5210 Power Adapter Harness to the installed spade taps. Connect the opposite end to the C-5602R1 Power Converter.
...
Connect the C-5500-84 Power Extension Harness to the appropriate connector on the C-5602R1 Power Converter. The remaining cable end connects to the FasCard reader.
...
| cci-readerinstall-kit |
|---|
| KitID | 700 |
|---|
| KitDesc | Factory Optical Coin Drop |
|---|
|
Disconnect the Coin Drop from the Machine Control Assembly. Connect the C-6250 Coin Sense Harness to the harness connected to the Coin Drop.
|
Connect Machine Interface Harness
| Cci readerinstall kit |
|---|
| KitID | 648 |
|---|
| KitDesc | Pulse - Coin |
|---|
|
Connect the C-5300-NC Machine Start Harness to the coin 1 connector on the Machine Control Assembly.| step |
|---|
|
|
| cci-readerinstall-kit |
|---|
| KitID | 582 |
|---|
| KitDesc | Serial Communication / Serial Pulse |
|---|
|
Connect the C-5240 Machine Start Harness to the the H3 connection on the Machine Control Assembly or Communication board.
|
Connect and Mount Reader
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | F2 Reader |
|---|
| PageWithExcerpt | _Reader Ports |
|---|
|
...
Feed remaining harness ends through the mounting hole.
...
(Pulse - Coin Only) If using the C-5300-NC Machine Start Harness, connect the free end to port 2 (Pulse Connection Port) as shown in the image above.
...
(Serial Comm Only) If using the C-5240 Machine Start Harness, connect the free end to port 5 (Serial Connection Port) as shown in the image above.
...
(Coin and Card Installations Only) Connect the free end of the C-6250 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
...
Machine Configuration
| Multiexcerpt include |
|---|
| SpaceWithExcerpt | CCIDOC |
|---|
| MultiExcerptName | ACA Configuration |
|---|
| PageWithExcerpt | _Machine Configuration |
|---|
|
...