Versions Compared

Old Version 4

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user David Bussman

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

...

Cci readerinstall step
componentMounting

  • Place the C-6700-TEMP Drill Template on the desired mounting location.

  • Verify included harnesses will reach desired location without encountering interference from internal machine components.

    • Refer to FasCard Mounting Guide for further instructions.
    cci-readerinstall-kitstep
    KitIDcomponent584
    KitDescCoin and Card

    Connect Power

    Power

    Cci readerinstall step
    componentCoin Sense

  • Tap the machine AC power wires using the C-5101 Spade Taps.

    1. For 120v models: L1, N, and Ground wires

    2. For 240v models: L1, L2, and Ground wires

    • Connect the three wires from the C-5210 Power Adapter Harness to theC-5101 Spade Taps.

    1. Connect the Blue wire to the L1 tap.

    2. Connect the Brown wire to the N/L2 tap.

    3. Connect the Green/Yellow wire to the Ground tap.

  • Connect the 3-pin connector from the C-5210 Power Adapter Harness to the matching connector on the C-5602R1 Power Converter.

  • Connect the 4-pin connector from the C-5602R1 Power Converter to the matching connector on the C-5500-84 Power Extension Harness.

  • Run the C-5500-84 Power Extension Harness to the reader mounting location.

    • Cci readerinstall kit
    KitID794719
    KitDescTap Source Machine Power

    ...

    Coin Drop - Factory Optical

    1. Disconnect coin drop from factory machine harness.

    2. Connect C-6360 Coin Sense Harness to the coin drop.

      1. Connect red to red.

      2. Connect green to brown.

      3. Connect blue to blue.

    Cci readerinstall step
    componentStart

    Cci readerinstall kit
    KitID639
    KitDescPulse - Coin Connection

    1. Connect the C-5262 Machine Start Harness to the harness originally connected to the coin drop.

      1. Connect to the black and brown wires.

      2. To prevent any potential electrical issues, apply electrical tape over the blue wire connector.

    Cci readerinstall step
    componentExtras

    Disconnect coin drop from factory machine harness
    Cci readerinstall kit
    KitID7191178
    KitDescCoin Drop - Factory Optical
    SAO - Coin and Card

    1. Run C-5262 Machine Start Harness and C-6360 Coin Sense Harness to the lower pocket control board.

    2. Connect C-6360 Coin Sense Harness to the coin drop for the lower pocket.

      1. Connect red to red.

      2. Connect green to brown.

      3. Connect blue to blue.

    Connect Machine Interface Harness

    KitDesc
    Cci readerinstall kit
    KitID636

    		Pulse - Coin Connection

    1. Connect the C-5256 5262 Machine Start Harness to the harness originally connected to the lower pocket’s coin drop.

      1. Connect to the black and brown wires.

      2. To prevent any potential electrical issues, apply electrical tape over the blue wire connector.

    2. Connect

    ...

    1. the C-6400 Stack Add-on Board to port 5 (Serial Connection Port) on the card reader.

      1. Connect the C-5262 Machine Start Harness connected to the lower pocket Machine Control Assembly to the J1 connection on the C-6400 Stack Add-on Board.

    2. Connect the C-6360 Coin Sense Harness connected to the lower pocket Coin Drop to port 4 (Coin 2 Sense Harness Connection Port) on the card reader.

    Cci readerinstall step
    componentReader

    Cci readerinstall footer