Versions Compared

Old Version 4

changes.mady.by.user Former user

Saved on

compared with

New Version Current

changes.mady.by.user Adam Arafat

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Import Macro Repair
div
Panel
borderColor
Class
darkred
toc-header
titleColor
section
white
column
titleBGColor
width
darkred
30
borderStyle
panel

Table of Contents
maxLevel2
minLevel2

Column
width70
Panel
titleOverview
solid
title
On this Page
Overview

This guide is intended to walk the installer through the internal power supply replacement of a V1 Control Head. 

Multiexcerpt include
SpaceWithExcerptcom.atlassian.confluence.content.render.xhtml.model.resource.identifiers.SpaceResourceIdentifier@7627108f
MultiExcerptNameNeedHelp
PageWithExcerptCCIDOC:_Contact Us

Multiexcerpt include
MultiExcerptNameWarning
DisableCachingtrue
PageWithExcerptCCIDOC:_General

Required

Hardware

parts & tools

Bw part list
Partsc-0525,C-0550,C-0551
SizingModeHeight
ShowDesc2false
ShowDesc3false

SingleRowtrue

Recommended

Tools

tools and

Supplies

supplies (

Not Included

not included)

  • Phillips Screwdriver
  • 3
/
  • -16" Hex Driver

Installation

Div
Classinstall-steps
panel

Step-by-step guide

Step 1 -

Remove

 Removing the Control Head from the X-Changer

Cabinet

cabinet

  1. Flip the white rocker switch on the rear of

the control head

  1. the Control Head to the

'Off'

  1. "OFF" position. 

    Image Added

  2. Disconnect all cables from the front and rear of the
control head
  1. Control Head unit. 
    1. CCI Technical Support recommends taking a
picture
    1. photo of the existing connections with a smartphone/camera
or smart phone
    1. as a reference for the re-installation process. 
  2. Remove the
screws securing the control head
  1. screws securing the Control Head wings to the X-Changer
frame
  1. mounting rack. 

Image Removed

Image Removed

  1. Image Added
Panel

Step 2 -

Remove Control Head Wings

Removing the Control Head wings

  1. Using
the
  1. the 3
/
  1. -16" Hex
driver
  1. Driver, remove the screws securing the wings
to the control head.
  1. on the sides of the Control Head. 
    1. Set the screws aside for reassembly. 

Image Removed

Image Removed

    1. Image Added
Panel

Step 3 -

Open

Opening the Control Head

  1. Remove the screws
indicated
  1. shown in the composite image below
.
  1. : 

    Image Added

  2. Slowly lift the top
panel - internal
  1. panel–internal cable connections will prevent it from being removed entirely. 
    1. Disconnect the USB cable. 
    2. Disconnect the parallel (ribbon) cables.
Top

    1. Image Added

  2. The top panel may now be
completely
  1. removed.

Image Removed

Image Removed

Panel
  1.  

Step 4 -

Remove Failed Power Supply

Removing the failed power supply 

  1. Note the location of the existing wires connected to the power supply that requires replacement. 
    1. The larger power supply is the
15 volt supply and the
    1. 15V supply. The smaller is the
12 volt
    1. 12V supply. 
    2. CCI Technical Support recommends taking a picture of the existing wire connections with a smartphone/camera
or smart phone
    1. as these connections
must
    1. must be exactly duplicated with the replacement power supply. 

      Image Added

  2. Remove the screws securing the wires to the power supply. 

    Image Added

  3. Remove the screws securing the power supply to
control head case (located on bottom of control head).
  1. the Control Head case. 


    Warning
    titlePower supply screws

    Please be aware that the screws for the power supply are located on the external underside of the Control Head case. Caution is required when removing them, as the power supply may come loose during removal. 

    Image Added

  2. Lift the power supply free of
the control head
  1. the Control Head case.
Image Removed

Image Removed

Image Removed

Panel

Step 5 -

Install Replacement Power Supply and Reconnect Control Head

Bw part list
Partsc-0550
SizingModeHeight
ShowDesc2false
ShowDesc3false
SingleRowtrue

  1. Reverse the process listed in Step 4 to install the power supply.
  2. Reverse the process listed in Step 3 to re-seal the control head.
  3. Reverse the process listed in Step 2 to reinstall the control head wings.
  4. Reverse the process listed in Step 1 to reinstall control head in the X-Changer cabinet.
Additional Information

Installing the replacement power supply and reconnecting the Control Head

  1. Reverse the steps listed from Step 4 to Step 1 to install the replacement power supply. 

    Note
    titleOrange plastic screw

    Turn the orange plastic screw adjacent to the wiring screws clockwise until it stops (do not overturn). 

Related documentation

Filter by label (Content by label)
title
showLabelsfalse
showSpacefalse
sortmodified
reversetrue
excludeCurrenttrue
cqllabel = "controlhead" and space = "LG" and type = "page"