Versions Compared

Old Version 4

changes.mady.by.user David Bussman

Saved on

compared with

New Version Current

changes.mady.by.user Chris Kite

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Cci readerinstall header

Install Mounting Hardware

Cci readerinstall kit
KitID616
KitDescCoin and Card

  1. Place theC-5700-TEMPDrill Template on the desired mounting location.

  2. Verify included harnesses will reach desired location without encountering interference from internal machine components.

  3. Refer to the for further instructions.

Cci readerinstall kit
KitID1047
KitDescCard Only - Card Model
  1. Remove any cover or card reader plate attached to the payment device mounting bracket.

  2. Place theC-5701 Mounting Plate behind the payment device mounting bracket and align the set of lower mounting points with that of the out set of threaded holes on the C-5701 Mounting Plate. Ensure the inner set of threaded holes are accessible through the central opening in the MayTag payment device bracket. Attach using (2) C-1060 8-32 x 3/8" Screws.

  3. Place the C-5700 Mounting Bracket over the front of the assembly so that the set of circular openings align with the threaded holes of the C-5701 Mounting Plate accessible through the central opening. Attach using the remaining (2) C-1060 8-32 x 3/8" Screws.

Connect Power

Cci readerinstall kit
KitID595
KitDescTap Machine Power

  1. Tap power as described in the document by connecting theC-5210Power Adapter Harnessto the power distribution panel inside the machine.

    1. 120vac: Connect the blue wire to L1 and the brown wire to N.

    2. 240vac: Connect the blue wire to L1 and the brown wire to L2.

    3. Connect the green wire to ground.

  2. Connect the opposite end of theC-5210Power Adapter Harnessto theC-5602R1Power Converter.

  3. Connect theC-5500Power Extension Harness to the appropriate connector on theC-5602R1Power Converter. The remaining cable end connects to the FasCard reader.

Connect Coin Sense Harness

Cci readerinstall kit
KitID693
KitDescFactory Coin Drop
  1. Disconnect the Coin Drop from the Machine Control Assembly.
  2. Connect theC-5362Coin Sense Harness to the harness connected to the Coin Drop.

Connect Machine Interface Harness

Cci readerinstall kit
KitID590
KitDescSerial Communication / MLV+ Pulse
  1. Connect theC-5364Machine Start Harness to theAA3connector on the Machine Control Assembly.

Connect and Mount Reader

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameF1 Reader
PageWithExcerpt_Reader Ports

  1. Feed remaining harness ends through the mounting hole as described in the F1 Reader Mounting Guide.
  2. Connect the free end of the C-5364 Machine Start Harness to port 1 (Serial Connection Port) as shown in the image above.
  3. (Coin and Card Installations Only) Connect the free end of the C-5362 Coin Sense Harness to port 3 (Coin Sense Harness Connection Port) as shown in the image above.
  4. Connect the free end of the C-5500 Power Extension Harness to port 4 (Power Harness Connection Port) as shown in the image above.
  5. Secure the FasCard reader as described in the F1 Reader Mounting Guide.

Machine Configuration

Multiexcerpt include
SpaceWithExcerptCCIDOC
MultiExcerptNameMayTag Gen1 MLV+ Pulse
PageWithExcerpt_Machine Configuration

Cci readerinstall footer