Versions Compared

Old Version 43

changes.mady.by.user Chris Kite

Saved on

compared with

New Version Current

changes.mady.by.user Adam Arafat

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Overview

This page is intended to guide the user through the replacement of a touchscreen monitor in

an

a LaundryCard X-Changer cabinet.

warning
Note
titleIMPORTANT

WARNING

Disconnect any electrical device from power before performing any work on the device. It is recommended that the instructions contained herein be performed by individuals who are qualified to perform these tasks. Card Concepts Inc. takes no responsibility for the accuracy of this document or any damage that may occur to target equipment. 

Minimum

A minimum of two (2) people is recommended for mounting/unmounting the touchscreen to the X-Changer cabinet.

Unmounting the Touchscreen

On this page

Table of Contents
minLevel1
maxLevel3
outlinefalse
styledefault
typelist
printablefalse

Step-by-step guide

Step 1 – Unmounting the monitor

  1. Disconnect any connected cables (power, video, touchscreen input (USB))

before proceeding

  1. from the monitor.

Image Removed

Unmount the existing monitor from the bracket.

Unmount existing monitor from cabinet.

For v1 cabinets, three (3) bracket

  1. Set the cables inside the cabinet so they can be used later.
    Image Added

  2. To begin unmounting the monitor, verify what cabinet version you are working with.

    1. In V1 cabinets remove the three kep nuts to the left and right of the touchscreen

should be unfastened to

    1. . Unfasten the kep nuts fully then pull the

mounting

    1. monitor assembly back toward you to remove

touchscreen. DO NOT

    1. it.

      1. Do not remove the four

(4)

      1. -center VESA screws

in this step if replacing a monitor in a v1 cabinet!This would also require unmounting the card dispenser tray, as the brackets share two of the same mounted bolt threads

      1. .

    2. For

v2

    1. V2 cabinets

, only

    1. remove the four

(4) VESA screws (Green) should be unfastened to unmount the touchscreen from its mounted bracket from the front of the X-Changer door

    1. center VESA screws and push the monitor outward.

      1. Do not remove the kep nights to the left and right of the mounting bracket.

v1 Cabinet (Elo)

v2 Cabinet (Elo / Zuljana)

Image Removed
Image Added
Image Removed

Mounting a New or Replacement Touchscreen

Info
  • Select the appropriate tab for instructions by cabinet version.
  • Monitor appearance may vary dependent upon changes made by the vendor.
Prior to
Image Added

Step 2 – Installing the replacement touchscreen

Before mounting a touchscreen to a specific cabinet type, the touchscreen will need to be

mounted

attached to its respective bezel.

Expand
titleVersion 1 Cabinet
Warning
titleK-1500-TS: Elo Touchscreen Kit

IMPORTANT

V1 Cabinets are not compatible with the Zuljana touchscreen.

DO NOT USE A ZULJANA TOUCHSCREEN WITH V1 CABINETS.

It is strongly recommended to use properly listed ELO touchscreens. Failure to do so may result in a non-working touchscreen and will not be supported by CCI.

Requirements

Image Removed

Install Components

Installation components

Cci kits
TypeParts
KitIDK-1500-TS
ShowKitIDtrue
ShowKitDesctrue
Tips
Tip

Upon removing the existing monitor, attach the monitor edge gasket (C-1380) to the cabinet

prior to Elo Touchscreen

before installing the new monitor.

Instructions

Step-by-step guide:

  1. Place the new touchscreen monitor face down on

monitor bezel. If

  1. the

new

  1. monitor

uses the same

  1. bezel

as the old monitor, you can remove the old touchscreen from its bezel to reuse the bezel component

  1. .

    1. Elo touchscreens use bezel C-1053B.

Image Removed
    1. Image Added

  2. Attach the bezel mounting screws to the touchscreen. Ensure the bezel remains as flush as possible with the touchscreen without recessing back.
    Image Modified

  3. Eight (8) screws will fasten into all eight (8) holes along the top, bottom, and sides of the monitor.

    • In some v1 cabinet instances, only the top and bottom four (4) holes would need to be fastened with bezel mounting screws.

  4. Place bracket (C-1056) across the back of the touchscreen monitor and attach supplied VESA mounting screws (

equivalent to

  1. C-1011) to the monitor.

Image Removed
  1. Image Added

  2. Attach the monitor edging (C-1380) to

cabinet prior to installation of

  1. the cabinet before installing the new monitor.

  2. Attach the bracket-mounted unit to the bolts on the front door of the cabinet from behind the door and tighten down using

existing

  1. the previously removed kep nuts.
    Image Modified

  2. Re-attach the cables to the newly installed monitor.

Image Removed
  1. Image Added

    1. Connect and hand-tighten screws from the blue VGA video cable.

    2. Connect the USB cable.

Attach

    1. Connect the barrel-shaped power supply cable.

Reboot

  1. Restart the computer.

Expand
titleVersion 2 Cabinet
Warning
title

Zuljana Touchscreens and Older LaundryCard

Zuljana touchscreens are only compatible with version 9 software.

DO NOT USE ZULJANA TOUCHSCREENS WITH V8 OR OLDER SOFTWARE.

Must either upgrade to LaundryCard v9 or utilize an Elo touchscreen.

Requirements

Image Removed

Version 2 Cabinet

Install Components

Installation components

Elo Touchscreen for older
Elo touchscreens w/ integrated bezel (K-1504-TSA)

Zuljana Touchscreen for older
Elo touchscreens w/ integrated bezel (K-1504-TSB)

Zuljana Touchscreen for existing
flat Elo touchscreens (K-1504-TSC)

Cci kits
TypeParts
KitIDK-1504-TSA
Cci kits
TypeParts
KitIDK-1504-TSB
Cci kits
TypeParts
KitIDK-1504-TSC

Step

1

-by-step guide:

ELO Touchscreen

Zuljana Touchscreen

Image Removed
Image Added
Image Removed
Image Added

  1. Place the new touchscreen monitor face down on the monitor bezel. If the new monitor uses the same bezel as the old monitor, you can remove the old touchscreen from its bezel to reuse the bezel component.

    1. ELO touchscreens use bezel C-1053B.

    2. Zuljana touchscreens use bezel C-1053B-V2.

Step 2

a

ELO Touchscreen

Zuljana Touchscreen

Image Removed
Image Added
Image Removed
Image Added

  1. Attach the bezel mounting screws to the touchscreen. Ensure the bezel remains as flush as possible with the touchscreen without recessing back.

    1. Eight (8) screws will fasten into all eight (8) holes along the top, bottom, and sides of the monitor.

Step 3

Image Removed

  1. Place the touchscreen with bezel attached back into the X-Changer door from the front. 

Step 4
  1. Image Added

Image Removed

  1. Secure the touchscreen to monitor using the provided VESA 75 screws while ensuring the display is high enough on the bracket to have the monitor buttons visible.

    Image Added
Warning
title

IMPORTANT

For Zuljana Touchscreen Monitors, DO NOT use screws longer than 8mm in length.

Step 5

Image Removed

  1. Re-attach cables to the newly installed monitor.

    1. Connect and hand-tighten screws from the blue VGA video cable.

    2. Connect the USB cable.

Attach

    1. Connect the barrel-shaped power supply cable.

Step 6
    1. Image Added

  2. Reboot the computer.

Configure and Calibrate the Touch Screen

The Configure Hardware Tool

Image Removed

The

Step 3 – Configuring and calibrating the touchscreen

The latest Configure Hardware tool within LaundryCard v9.1.9 or newer

is able to

can recognize whether the installed touchscreen is an Elo or Zuljana touchscreen and apply the appropriate settings.

Image Added

  1. After the hardware

install

  1. installation, open Windows Explorer by either pressing the Windows Key and clicking the Windows Explorer colored manila folder or

use

  1. using the Windows shortcut WIN+E.

  2. Navigate to D:\Setup\InstallProcs.

  3. Run the configurehardware.cmd script.

  4. Select option G to configure just the touchscreen.

The appropriate drivers and settings (including the Calibration Tool for Elo touchscreens) will then

install

be installed.

When an Elo touchscreen is installed, direct interaction with the touchscreen may be required if the display is not already calibrated.

With Zuljana touchscreens, Configure Hardware will restart the system after a new monitor

install

is installed before reaching the diagnostic screen for post-config testing

,

if a Zuljana touchscreen has never been used on the X-Changer in question.

Note
title

Note

If the Zuljana touchscreen is not recognized on a V9 system after

install

installation, update the LaundryCard application to v9.1.9 or newer.

Manual Calibration (Elo Only)

Note
title

Note

Zuljana Touchscreen Monitors use a ten (10) finger-capacitive multitouch panel and do not require calibration.

However, certain functions will need to be modified at a software level to accommodate for regular X-Changer use.

Please contact CCI Technical Support for further information and assistance.

Image Removed
Image Added

Upon rebooting the computer:

  1. When KeepAGoin is visible and the startup countdown displays, select the Pause button on the screen.

    • May take a couple of tries if the monitor is poorly uncalibrated.

  2. Press the Windows key on the keyboard to bring up the taskbar.

  3. Begin typing the application name 'Control Panel' until the search populates the Control Panel.

  4. Select the control panel settings option 'Elo Touchscreen'.

    • (If you do not see the settings option then the Elo software will need to be installed.)

  5. Under the "Properties 1" tab, click the Align button and follow the prompts to align the touchscreen.

  6. Close the Elo Touchscreen Control Panel window and bring back up the KeepAGoin window.

  7. Click the Refresh button to restart the startup countdown.

Filter by label (Content by label)
showLabelsfalse
maxCheckboxfalse
sortmodified
showSpacefalse
reversetrue
titleRelated articles
cqllabel = "touchscreen"